Frick QUANTUM - Index

FRICK
®
QUANTUM™ COMPRESSOR CONTROL PANEL S90-010 O
OPERATION Page 107
Index
A
About .………………………………………………………..14
Activated .…....................................................................23
Active ..……......................................................................8
Actual ..……....................................................................19
Additional Auxiliaries.......................................................17
Alarm ..……. ....................................4, 7, 14-16, 20, 23, 24
Alarm Delay ... .............................................20, 23, 24
Alarm Silence...........................................................15
Alarm Status .. ...........................................................7
Alarm Shutdown History...........................................15
Alarm Shutdowns...............................................14, 15
Allen-Bradley...................................................................79
Analog Auxiliaries Disable...............................................82
Analog Auxiliaries Enable ...............................................82
Analog Board 1 Comm. Fail - Shutdown.........................93
Analog Board 2 Comm. Fail - Shutdown.........................93
Auto .………..................................................................4, 9
Automatic .....................................................................4, 9
Auxiliaries 3-8............................................................14, 81
Auxiliary
1……..…………………………………………………..80
1 and 2 ....................................................................80
1 and 2 - Disable......................................................80
1 Checked Always ...................................................60
1 Checked Running .................................................60
1 Type Shutdown.....................................................60
2 ………...................................................................80
Alarm ………………………………………………….93
Analog …………………………………….14, 17, 72, 82
1 Checked Always ............................................43
1 Checked Running ..........................................43
Change Setpoints .............................................43
High Alarm........................................................42
High Alarm Delay..............................................42
High Shutdown .................................................42
High Shutdown Delay .......................................42
Low Alarm.........................................................42
Low Alarm Delay...............................................42
Low Shutdown ..................................................43
Low Shutdown Delay........................................43
Temperatures and Pressures .....................14, 72
Inputs Disable ..........................................................81
Inputs Enable...........................................................81
Shutdown.................................................................93
Setup ... .............................................................40, 80
“x” Disable................................................................41
“x” Enable.................................................................41
B
Balance Piston ..................................................................9
Balance Piston Failure Shutdown ...................................93
C
Calibrate
Auxiliary Analog ...............................14, 65, 71, 72, 82
Balance Piston Pressure..........................................66
Discharge Pressure .................................................66
Discharge Temperature ...........................................67
Entering Process Temperature ................................67
Filter Pressure..........................................................66
Kilowatt Monitor .................................................75, 82
Disable..............................................................82
Enable ..............................................................82
Leaving Process Temperature.................................67
Level Position ..........................................................71
Motor Current.....................................................65, 67
Oil Pressure.............................................................66
Oil Temperature.......................................................67
Pressure ..................................................................66
Remote Control Setpoint.................. 14, 65, 70, 82, 92
Separator Temperature............................................67
Slide Stop ................................................................68
Decrease Slide Stop.........................................68
Increase Slide Stop...........................................68
Set Maximum Point...........................................68
Set Minimum Point............................................68
Slide Valve Calibration......................................68
Unload Slide Valve ...........................................68
Slide Valve...............................................................69
Decrease Slide Stop.........................................69
Load Slide Valve...............................................69
Set Maximum Point...........................................69
Set Minimum Point............................................69
Slide Stop Calibration .......................................69
Unload Slide Valve ...........................................69
Slide Valve and Slide Stop.................................14, 65
Slide Valve Position............................... 14, 65, 82, 92
Suction Pressure .....................................................66
Suction Temperature ...............................................67
System Discharge Pressure ....................................66
Temperature ............................................................67
Calibration ................................................................14, 64
Pressure Transducer Ranges and Offsets...............65
Temp. Probe Types, Ranges and Offsets................65
Setpoints............................................................66, 67
Cancel .……......................................................................6
Capacity ..… .........................................................9, 76, 92
Capacity Control ...............................14, 17, 18, 40, 52, 53
Box .….......................................................................8
Disable Mode...........................................................79
Enable Mode............................................................79
Options …………………………………………………14
Setpoints Displays ...................................................18
Source Keypad ..........................................................8
Source Remote Comm. .............................................8
Source Remote-I/O....................................................8
Capacity Manual Load ....................................................12
Capacity Mode Auto .…..................................................12
Capacity Mode Remote...................................................12
Capacity Mode Manual Unload.......................................12
Change Communications................................................78
Change Current Time and Date......................................76
Change Screen Settings.................................................83
Change Setpoints .............................................................6
Change To Pressure.......................................................19
Change To Temperature.................................................19
Clear Alarms .............................................................14, 15
Common Terminology.......................................................4
Communication Ports Status.............................................8
Communication Protocol.................................................79
Communications - Change Baud ....................................78
Communications - Change Setpoints..............................78
Communications Box........................................................8
Compressor
Alarm Status Box - Alarm...........................................8
Alarm Status Box - Shutdown....................................8
Auto .…....................................................................11