Frick QUANTUM - Page 112

S90-010 O FRICK
®
QUANTUM™ COMPRESSOR CONTROL PANEL
Page 112 OPERATION
Setback Schedule Setpoints Start.................................. 38
Setback Schedule Setpoints Stop .................................. 38
Setback Setpoints .......................................................... 17
Setpoint …...................................................................... 19
Setpoint Box Actual ....................................................... 8
Setpoint Box Setpoint....................................................... 8
Setup For Automatic Control .......................................... 91
Show Comms................................................................. 88
Shutdown ………………………………………..4, 15, 16, 93
Shutdown - Digital Board Reset ..................................... 94
Shutdown Delay ..................................................20, 23, 24
Slide Stop ……..………………………………………….9, 12
Slide Stop Mode Manual Decrease................................ 12
Slide Stop Mode Mode Auto........................................... 12
Slide Stop Mode Manual Increase.................................. 12
Slide Valve . ..........................................................9, 36, 37
Economizer Setpoints ........................................36, 37
Highest S.V. Position to allow Comp. Start ...... 36
Hot Gas Bypass/Slide Valve Setpoint .............. 36
Off when below ................................................ 37
On when above................................................ 37
On when below ................................................ 36
Setpoints.....................................................36, 37
Starting Period Before S. V. Will Load ............. 36
Stopping Period Slide Valve Unload ................ 36
Slide Valve And Slide Stop Status Box ..................... 9
Slide Valve Mode Auto............................................ 11
Slide Valve Mode Manual Load............................... 11
Slide Valve Mode Manual Unload ........................... 11
Position ..............................................................18, 51
Position Control Disable.......................................... 82
Position Control Enable........................................... 82
Remote.................................................................... 11
Remote Slide Valve................................................. 11
Setpoints ......................................................14, 17, 81
Start …….……………………………………………………19
Start Autocycle ............................................................... 19
Start Time Delay............................................................. 19
Starting..….. ................................................................... 23
Starting Differential Pressure below ............................... 23
Starting Failure............................................................... 98
Starting Superheat Shutdown......................................... 98
Status Box of Oil Lubrication Devices Oil Pump............... 8
Stop .……… ....................................................9, 19, 22, 23
Autocycle................................................................. 19
Time Delay.............................................................. 19
Suction Pressure ..7-10, 12, 18, 19, 23, 24, 33, 35, 43, 46,
61, 81, 93, 95-97
Pull Down................................................................ 81
Pull-Down - Disable................................................. 81
Pull-Down - Enable.................................................. 81
Reduction Step Amount of Time ............................. 61
Reduction Step Pressure Band............................... 61
Sensor Fault............................................................ 98
Suction Pull Down .......................................................... 40
T
Temperature Calibration................................................. 82
Temperature Mode 2.........................................................8
Temperature Units.....................................................76, 77
the Real Time Trending...................................................87
Tuning a PID Controller...................................................46
Turbine .….. ..............................................................29, 30
4–20 ma analog input...............................................29
4–20 ma analog output ............................................29
Confirmed Running (RPM).......................................30
Cycle Time...............................................................29
Drive Output at Max SV position ..............................29
Hardware Signals.....................................................29
High RPM Alarm ......................................................30
High RPM Alarm Delay ............................................30
High RPM Shutdown................................................30
High RPM Shutdown Delay......................................30
Idle Speed................................................................29
Low RPM Alarm .......................................................30
Low RPM Alarm Delay.............................................30
Low RPM Force Unload...........................................30
Low RPM Shutdown.................................................30
Low RPM Shutdown Delay ......................................30
Low RPM Stop Load ................................................30
Maximum output.......................................................29
Minimum output........................................................29
Rate of change.........................................................29
Slide Valve Position to begin Speed Increase..........29
Starting Maximum Delay..........................................30
U
Unload ..….. ......................................................................9
Unload Slide Valve..........................................................68
Up One ..…. ......................................................................6
Upper Cycle Time............................................................19
Upper Dead Band............................................................19
Upper Proportional Band.................................................19
V
VFD .……… ....................................................................27
4 – 20 ma analog input.............................................27
4 – 20 ma analog output ..........................................27
Cycle Time...............................................................27
Drive Output at Max SV position ..............................27
Hardware Signals.....................................................27
Maximum output.......................................................27
Minimum output........................................................27
Rate of change.........................................................27
Setpoints..................................................................27
Slide Valve Position to begin Speed Increase..........27
VI OverRide ....................................................................10
W
Warm Up Load Inhibit........................................................9
Warning .…. ......................................................................6
Y
York ISN .… ....................................................................79
YORK Refrigeration Systems
100 CV Avenue, P.O. Box 997 Waynesboro, Pennsylvania USA 17268-0997
Phone: 717-762-2121 •
Fax: 717-762-8624 • www.frickcold.com
Copyright
®
2004 YORK Refrigeration Systems