Message Explanation and/or corrective action Level
Keyboard hook loaded OK
The keyboard hook dll exists and loaded successfully. LOG_EX
L after Ctrl Processing the backdoor entry. LOG_EX
Loading keyboard hook
When AppLock first loads, it loads a dll that contains the keyboard hook processing. This message is logged
prior to the load attempt.
LOG_PROC-
ESSING
Open failure
The status information is being saved to a file and the file open has failed. This could occur if the file is write pro-
tected. If the file does not exist, it is created.
LOG_ERROR
Open registry failure
If the Administration registry key does not exist, the switch to user mode fails because the AppName value in
the Administration key is not available.
LOG_ERROR
Opened status file The status information is being saved to a file and the file has been opened successfully. LOG_EX
Out of memory for
encrypted pwd
Not enough memory to encrypt the password. LOG_ERROR
pRealTaskbarWndProc
already set
The taskbar control has already been installed. LOG_EX
Pwd cancelled or invalid-
remain in user mode
The password prompt was cancelled by the user or the maximum number of failed attempts to enter a pass-
word was exceeded.
LOG_EX
Read registry error-hot
key
The hotkey registry entry is missing or empty. This is not considered an error. The keyboard hook uses an
embedded default if the value is not set in the registry.
LOG_ERROR
Read registry failure-app
name
AppName registry value does not exist or is empty. This constitutes a failure for switching into user mode. LOG_ERROR
Read registry failure-Cmd
Line
AppCommandLine registry entry is missing or empty. This is not considered an error since command line infor-
mation is not necessary to launch and lock the application.
LOG_ERROR
Read registry failure-Inter-
net
The Internet registry entry is missing or empty. This is not considered an error since the Internet value is not
necessary to launch and lock the application.
LOG_ERROR
Registering Backdoor
MSG
The AppLock system communicates with the keyboard hook via a user defined message. Both AppLock.exe
and Kbdhook.dll register the message at initialization.
LOG_PROC-
ESSING
Registering Hotkey MSG
The AppLock system communicates with the keyboard hook via a user defined message. Both Applock.exe
and Kbdhook.dll register the message at initialization.
LOG_PROC-
ESSING
Registry read failure at
reenter user mode
The registry has to be read when entering user mode is the AppName is missing. This user mode entry is
attempted at boot and after a hotkey switch when the administrator has closed the application being locked or
has changed the application name or command line.
LOG_ERROR
Registry read failure at
reenter user mode
The registry has to be read when switching into user mode. This is because the administrator can change the
settings during administration mode. The read of the registry failed which means the Administration key was
not found or the AppName value was missing or empty.
LOG_ERROR
Registry read failure
The registry read failed. The registry information read when this message is logged is the application infor-
mation. It the Administration key cannot be opened or if the AppName value is missing or empty, this error is
logged. The other application information is not required. If the AppName value is not available, AppLock can-
not switch into user mode.
LOG_ERROR
Reset system work area
failure
The system work area is adjusted when in user mode to cover the taskbar area. The system work area has to
be adjusted to exclude the taskbar area in administration mode. AppLock was unable to adjust this area.
LOG_ERROR
Shift pressed The Shift key has been pressed and trapped by the HotKey processing. LOG_EX
Shift Processing the hotkey and backdoor entry LOG_EX
Show taskbar The taskbar is now being made visible and enabled.
LOG_PROC-
ESSING
Switching to admin-back-
door
The system is currently in user mode and is now switching to admin mode. The switch occurred because of the
backdoor key presses were entered by the administrator.
LOG_PROC-
ESSING
Switching to admin-hotkey
press
The system is currently in user mode and is now switching to admin mode. The switch occurred because of a
hotkey press by the administrator.
LOG_PROC-
ESSING
4-54
To Next Page
Loading...
Need help?
General
Weight and Dimensions
