EasyManuals Logo

Honeywell MX7 Tecton Reference Manual

Honeywell MX7 Tecton
366 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #93 background imageLoading...
Page #93 background image
Message Explanation and/or corrective action Level
Switching to admin-
kbdhook.dll not found
The keyboard hook load failed, so AppLock switches to admin mode. If a password is specified, the password
prompt is displayed and remains until a valid password is entered.
LOG_PROC-
ESSING
Switching to admin-key-
board hook initialization fail-
ure
If the keyboard hook initialization fails, AppLock switches to admin mode. If a password is specified, the pass-
word prompt is displayed and remains until a valid password is entered.
LOG_PROC-
ESSING
Switching to admin-reg-
istry read failure
See the explanation of the “Registry read failure” above. AppLock is switching into Admin mode. If a password
has been configured, the prompt willbe displayed and will not be dismissed until a valid password is entered.
LOG_PROC-
ESSING
Switching to Task-
barScreenMode
In administration mode, the taskbar is visible and enabled. LOG_EX
Switching to user mode The registry was successfully read and AppLock is starting the process to switch to user mode.
LOG_PROC-
ESSING
Switching to user-hotkey
press
The system is currently in admin mode and is now switching to user mode. The switch occurred because of a
hotkey press by the administrator.
LOG_PROC-
ESSING
Taskbar hook failure AppLock is unable to control the taskbar to prevent the locked application from re-enabling it. LOG_ERROR
Taskbar hook OK AppLock successfully installed control of the taskbar. LOG_EX
Timeout looking for app
window
After the application is launched, AppLock must wait until the application has initialized itself before proceeding.
The application did not start successfully and AppLock has timed out.
LOG_ERROR
ToUser after admin, not at
boot
The user mode switch is attempted when the device boots and after the administrator presses the hotkey. The
mode switch is being attempted after a hotkey press.
LOG_EX
ToUser after admin-app
still open
The switch to user mode is being made via a hotkey press and the administrator has left the application open
and has not made any changes in the configuration.
LOG_EX
ToUser after admin-no
app or cmd line change
If user mode is being entered via a hotkey press, the administrator may have left the configured application
open. If so, AppLock does not launch the application again unless a new application or command line has been
specified; otherwise, it just locks it.
LOG_EX
Unable to move desktop
The desktop is moved when switching into user mode. This prevents them from being visible if the application is
exited and restarted by the timer. This error does not affect the screen mode switch; processing continues.
LOG_ERROR
Unable to move taskbar
The taskbar is moved when switching into user mode. This prevents them from being visible if the application is
exited and restarted by the timer. This error does not affect the screen mode switch; processing continues.
LOG_ERROR
Unhook taskbar wndproc
failure
AppLock could not remove its control of the taskbar. This error does not affect AppLock processing LOG_ERROR
Unhook wndproc failure AppLock could not remove the hook that allows monitoring of the application. LOG_ERROR
Unhooking taskbar
In administration mode, the taskbar should return to normal operation, so AppLock’s control of the taskbar
should be removed.
LOG_EX
Unhooking wndproc
When the administrator leaves user mode, the device is fully operational; therefore, AppLock must stop mon-
itoring the locked application.
LOG_EX
WM_SIZE adjusted This message denotes that AppLock has readjusted the window size. LOG_EX
X after Ctrl+L Processing the backdoor entry. LOG_EX
Ret from password <#> Return value from password dialog. LOG_EX
Decrypt data len <#> Length of decrypted password. LOG_EX
Window handle to enum-
windows=%x
The window handle that is passed to the enumeration function. This message can be used by engineering with
other development tools to trouble shoot application lock failures.
LOG_EX
WM_WINDOWPOSCHG
adjusted=%x
Output the window size after it has been adjusted by AppLock LOG_EX
4-55

Table of Contents

Other manuals for Honeywell MX7 Tecton

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Honeywell MX7 Tecton and is the answer not in the manual?

Honeywell MX7 Tecton Specifications

General IconGeneral
Display diagonal3.5 \
Display resolution240 x 320 pixels
Display number of colors-
Internal memory0.256 GB
Internal memory typeRAM
Compatible memory cardsSD
Maximum memory card size4 GB
Processor familyPXA 320
Processor frequency0.806 GHz
GPS (satellite)No
Operating system installed Windows CE 6.0
Wi-Fi standards802.11a, 802.11b, 802.11g
Bluetooth version2.0+EDR
Headphone outputs1
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)-30 - 50 °C
Operating relative humidity (H-H)5 - 100 %
Battery capacity2200 mAh
AC adapter output current7.4 A
Product colorBlack, Blue
Keyboard layoutAlphanumeric
Linear (1D) barcodes supportedCodabar, Code 128, Code 39, Code 93, EAN-13, GS1-128 (UCC/EAN-128), PLANET, Plessey, Telepen, Trioptic, U.P.C.
2D (matrix & stacked) barcodes supportedAztec Code, Code 49, Data Matrix, MaxiCode, MicroPDF417, PDF417, QR Code
Weight and Dimensions IconWeight and Dimensions
Depth50 mm
Width86 mm
Height223 mm
Weight595 g

Related product manuals