HP ProCurve 5400zl

filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)■
■ cv_out_flash < primary | secondary > -- Copy from primary/secondary flash. (p. 108)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ cv_out_flash < primary | secondary > -- Copy from primary/secondary flash. (p. 108)
■ copy running-config -- Copy running configuration file. (p. 123)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ copy startup-config -- Copy in-flash configuration file. (p. 123)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ copy tftp -- Copy data from a TFTP server. (p. 124)
■ autorun-cert-file -- Copy autorun trusted certificate to the switch. (p. 105)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ append -- Add the key(s) for operator access. (p. 102)
■ manager -- Replace the key(s) for manager access; follow with the 'append' option
to add the key(s). (p. 117)
■ append -- Add the key(s) for access. (p. 102)
■ operator -- Replace the key(s) for operator access (default); follow with the 'append'
option to add the key(s). (p. 119)
■ append -- Add the key(s) for access. (p. 102)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ append -- Add the key(s) for operator access. (p. 102)
■ manager -- Replace the key(s) for manager access; follow with the 'append' option
to add the key(s). (p. 117)
■ append -- Add the key(s) for access. (p. 102)
■ operator -- Replace the key(s) for operator access (default); follow with the 'append'
option to add the key(s). (p. 119)
99© 2009 Hewlett-Packard Development Company, L.P.
copyCommand Line Interface Reference Guide