HP ProCurve 5400zl User Manual

■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is
5. (p. 486)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 489)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 477)
■ normal -- Define a "normal" area. (p. 482)
■ nssa < 0 to 16777215 > -- Define a "not-so-stubby" area (or NSSA) and its cost. (p. 483)
■ metric-type < type1 | type2 > -- Metric type of the type-7 default. (p. 482)
■ no-summary -- Do not send summary LSA into the area. (p. 482)
■ range -- Summarize routes matching address/MASK pair. (p. 484)
■ ip -- Specify IP address/MASK pair. (IP-ADDR/MASK-LENGTH) (p. 481)
■ no-advertise -- Do not advertise the range outside the area. (p. 482)
■ type < summary | nssa > -- Link state database type to apply the range. (p. 491)
■ stub -- Define a "stub" area and specify its cost. (p. 489)
■ cost < 0 to 16777215 > -- Enter cost to use when injecting default routes into the
area. (p. 478)
■ no-summary -- Do not send summary LSA into the area. (p. 482)
■ virtual-link -- Specify a virtual neighbor. (IP-ADDR) (p. 492)
■ authentication -- Disable authentication. (p. 476)
■ authentication-key -- Set simple authentication method and key. (p. 476)
■ authentication-key -- OSPF authentication key (maximum 8 characters).
(OCTET-STR) (p. 476)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 478)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 480)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 481)
■ chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p.
478)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is
5. (p. 486)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 489)
■ default-metric < 0 to 16777215 > -- The default metric used for advertising external routes
imported into OSPF by this router (p. 478)
■ distance -- Set administrative distance to associate with intra-area, inter-area and AS-external
routes learned by OSPF (p. 479)
■ external < 1 to 255 > -- Set administrative distance to associate with external routes learned
by OSPF. (p. 479)
■ inter-area < 1 to 255 > -- Set administrative distance to associate with inter-area routes
learned by OSPF. (p. 480)
■ intra-area < 1 to 255 > -- Set administrative distance to associate with intra-area routes
learned by OSPF. (p. 480)
■ metric-type < type1 | type2 > -- The default metric type used for advertising external routes
imported into OSPF by this router (p. 482)
■ redistribute < connected | static | rip > -- Specify source protocols which will be redistributed
into OSPF (p. 485)
■ restrict -- Prevent redistribution of routes via OSPF (p. 485)
■ ip-addr -- Prevent redistribution of routes via OSPF (IP-ADDR/MASK-LENGTH) (p. 481)
■ rfc1583-compatibility -- Enable/disable RFC-1583 compatibility (p. 486)
■ trap < virtual-interface-state-change | neighbor-state-change | virtual-neighbor-state-change
| ... > -- Enable/disable OSPF traps (p. 489)
■ [no] router pim -- Enable/disable/configure PIM protocol on the device, or enter PIM Configuration
Context (p. 484)
■ bsr-candidate -- Configure the router to advertise itself as the Candidate Bootstrap Router
(Candidate-BSR) for a PIM-SM domain (p. 477)
472© 2009 Hewlett-Packard Development Company, L.P.
routerCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English