IBM SAN Volume Controller 2145-CG8 User Manual

225. SAN Volume Controller 2145-8A4
operator-information panel .......227
226. SAN Volume Controller 2145-8G4
operator-information panel .......228
227. SAN Volume Controller 2145-8G4 video, USB,
and the CD/DVD cables ........229
228. SAN Volume Controller 2145-8G4 air baffle 230
229. SAN Volume Controller 2145-8G4 fan 3 231
230. SAN Volume Controller 2145-8G4 dummy
CD/DVD drive ...........231
231. Replacing the operator-information panel 232
232. Disconnecting the SAN Volume Controller
2145-CG8 or 2145-CF8 operator-information
panel cable ............234
233. SAN Volume Controller 2145-8A4
operator-information panel .......235
234. Connectors for the operator-information panel
on the SAN Volume Controller 2145-8A4
system board ...........235
235. Connecting the SAN Volume Controller
2145-CG8 or 2145-CF8 operator-information
panel cable ............237
236. Raising the SAN Volume Controller 2145-CF8
or 2145-CG8 locking levers of the slide rails
of the rack ............238
237. Connectors for the operator-information panel
on the SAN Volume Controller 2145-8A4
system board ...........238
238. SAN Volume Controller 2145-CG8 or
2145-CF8 fan locations and connectors . . . 240
239. Removing or replacing a fan in the SAN
Volume Controller 2145-CG8 or 2145-CF8
node ..............241
240. Connectors for the SAN Volume Controller
2145-8A4 heat exchange fans ......242
241. SAN Volume Controller 2145-8G4 fan doors,
locations, and connectors .......243
242. SAN Volume Controller 2145-8F2 with the
access doors open ..........244
243. SAN Volume Controller 2145-8F2 fan
locations .............244
244. SAN Volume Controller 2145-CG8 or
2145-CF8 fan locations and connectors . . . 245
245. Removing or replacing a fan in the SAN
Volume Controller 2145-CG8 or 2145-CF8
node ..............246
246. Raising the SAN Volume Controller 2145-CF8
or 2145-CG8 locking levers of the slide rails
of the rack ............247
247. A close up of the SAN Volume Controller
2145-8A4 fan ............248
248. Routing the SAN Volume Controller 2145-8A4
fan cable .............248
249. SAN Volume Controller 2145-8G4 fan doors,
locations, and connectors .......249
250. Removing the heat sink from the SAN
Volume Controller 2145-CG8 or 2145-CF8
microprocessor ...........252
251. Opening the SAN Volume Controller
2145-CG8 or 2145-CF8 microprocessor-bracket
frame ..............253
252. Aligning the microprocessor installation tool 254
253. Lifting the microprocessor out of the
microprocessor bracket frame ......254
254. SAN Volume Controller 2145-8A4 air baffle
and heat-exchanger assembly ......255
255. The SAN Volume Controller 2145-8A4
microprocessor bracket frame fully opened . 256
256. Removing the heat sink from the
microprocessor ...........257
257. The microprocessor release lever and bracket
frame fully opened..........257
258. Location of the microprocessor and VRM
sockets..............258
259. Opening the SAN Volume Controller
2145-CG8 or 2145-CF8 microprocessor-bracket
frame ..............260
260. Removing the plastic protective cover from a
microprocessor ...........261
261. Inserting the microprocessor into the socket 261
262. Closing the SAN Volume Controller 2145-CG8
or 2145-CF8 microprocessor-bracket frame . . 262
263. Applying thermal grease to the SAN Volume
Controller 2145-CG8 or 2145-CF8
microprocessor ...........263
264. Installing the heat sink on the SAN Volume
Controller 2145-CG8 or 2145-CF8
microprocessor ...........263
265. Raising the SAN Volume Controller 2145-CF8
or 2145-CG8 locking levers of the slide rails
of the rack ............264
266. SAN Volume Controller 2145-8A4
microprocessor ...........265
267. Complete set of nine thermal grease dots on
the SAN Volume Controller 2145-8A4
microprocessor ...........266
268. Alignment pins on the SAN Volume
Controller 2145-8A4 heat-exchanger assembly . 266
269. Aligning the microprocessor with the socket 268
270. Installing the heat sink ........268
271. Microprocessor locking lever in open position 269
272. Microprocessor and heat sink locations 270
273. Location of the microprocessor and VRM
sockets..............271
274. Removing and replacing the SAN Volume
Controller 2145-CG8 or 2145-CF8 system
board ..............274
275. Connectors that are used on the SAN Volume
Controller 2145-8A4 system board ....276
276. SAN Volume Controller 2145-8A4 SATA cable
connectors ............277
277. SAN Volume Controller 2145-8A4 power
supply connectors ..........277
278. The IDE connector on the SAN Volume
Controller 2145-8A4 system board ....278
279. Connectors for the SAN Volume Controller
2145-8A4 heat exchange fans ......279
280. SAN Volume Controller 2145-8A4 system
board and microprocessor retention module . 280
281. Connectors on the SAN Volume Controller
2145-8G4 system board ........282
Figures ix
|
|
||
|
|
||
|
||
|
|
||
|
||
|
|
||
|
|
||
||
|
||
|
||
||
|
|
||
|
|
||
|
|
||

IBM SAN Volume Controller 2145-CG8 Specifications

General

Brand	IBM
Model	SAN Volume Controller 2145-CG8
Category	Storage
Language	English