IBM SAN Volume Controller 2145-CG8 User Manual

282. Left air baffle on the SAN Volume Controller
2145-8G4 .............282
283. Connectors on the right front side of the SAN
Volume Controller 2145-8G4 system board . . 283
284. Disk power cable connector and power
backplane on the SAN Volume Controller
2145-8G4 system board ........284
285. Right air baffle on the SAN Volume
Controller 2145-8G4 system board ....284
286. Removing thermal grease from the SAN
Volume Controller 2145-8G4 microprocessor . 285
287. Serial and video ports on the SAN Volume
Controller 2145-8G4 .........286
288. The placement of the screws that secure the
SAN Volume Controller 2145-8G4 system
board ..............286
289. SAN Volume Controller 2145-8G4 system
board ..............287
290. Removing and replacing the SAN Volume
Controller 2145-CG8 or 2145-CF8 system
board ..............289
291. Raising the SAN Volume Controller 2145-CF8
or 2145-CG8 locking levers of the slide rails
of the rack ............290
292. The SAN Volume Controller 2145-8A4
microprocessor bracket frame fully opened . 291
293. SAN Volume Controller 2145-8G4 system
board ..............294
294. The placement of the screws that secure the
SAN Volume Controller 2145-8G4 system
board ..............295
295. Serial and video ports on the SAN Volume
Controller 2145-8G4 .........295
296. Installing the microprocessor ......296
297. Estimating the position of the thermal grease
dots...............297
298. Complete set of nine thermal grease dots on
the microprocessor ..........297
299. Right air baffle on the SAN Volume
Controller 2145-8G4 system board ....298
300. Connectors on the right front side of the SAN
Volume Controller 2145-8G4 system board . . 299
301. Left air baffle on the SAN Volume Controller
2145-8G4 .............300
302. Connectors on the SAN Volume Controller
2145-8G4 system board ........300
303. Attaching the mounting plates ......303
304. Power cable clips ..........304
305. 2145 UPS-1U power cable-retention bracket
hardware .............305
306. 2145 UPS-1U power cable-retention bracket 305
307. 2145 UPS-1U power cable-retention bracket 306
308. The 2145 UPS-1U front-panel assembly 307
309. 2145 UPS-1U (rear view) ........307
310. Removing the 2145 UPS-1U front panel 308
311. The 2145 UPS-1U internal-battery connector 308
312. The 2145 UPS-1U internal battery connector
with protective tape .........309
313. Mounting screws for the 2145 UPS-1U 309
314. Installing the support rails for a 2145 UPS-1U
into the rack ............310
315. Mounting screws for the 2145 UPS-1U 311
316. Removing the 2145 UPS-1U front panel 311
317. The 2145 UPS-1U internal battery connector
with protective tape .........312
318. The 2145 UPS-1U with internal battery
connectors in place..........312
319. The 2145 UPS-1U cable retention bracket
connected to the 2145 UPS-1U ......313
320. 2145 UPS-1U (rear view) ........313
321. 2145 UPS-1U front-panel assembly ....313
322. Removing the front screws from the 2145
UPS-1U .............314
323. Removing the front rail on the 2145 UPS-1U 314
324. Removing the rear rail on the 2145 UPS-1U 315
325. Installing the support rails for a 2145 UPS-1U
into the rack ............315
326. Adjusting the rail depth on the 2145 UPS-1U 316
327. Securing the rear rail on the 2145 UPS-1U 316
328. Securing the front rail on the 2145 UPS-1U 317
329. Front and back panels for the 2145 UPS-1U 318
330. Removing the 2145 UPS-1U front panel 319
331. The 2145 UPS-1U internal battery connector
with protective tape .........319
332. Removing the 2145 UPS-1U battery ....320
333. Replacing the 2145 UPS-1U battery ....321
334. The 2145 UPS-1U internal-battery connector 321
335. Replacing the 2145 UPS-1U front panel 322
x IBM SAN Volume Controller Hardware Maintenance Guide
|
|
||

IBM SAN Volume Controller 2145-CG8 Specifications

General

Brand	IBM
Model	SAN Volume Controller 2145-CG8
Category	Storage
Language	English