IDEC OpenNet series User Manual

INDEX
ii OPENNET CONTROLLER USER’S MANUAL
command
execution 23-2
result code 23-3
string 23-3
general command mode 23-2, 23-6
ATOB 14-11
ATOH 14-7
ATZ 23-2, 23-5, 23-7
auto tuning 20-9
average 19-6
AVRG 19-6
B basic
instructions 7-1
system 1-6
BCC (block check character) 17-8, 17-18
BCD
left shift 13-13
to ASCII 14-9
to hex 14-3
BCDLS 13-13
bidirectional shift register 7-23
binary arithmetic instructions 11-1
bit
designation of link register 6-19
shift/rotate instructions 13-1
stack register 7-7
block move 9-8
BMOV 9-8
Boolean computation instructions 12-1
BPS, BRD, and BPP instructions 7-6
breakdown of END processing time A-2
BTOA 14-9
BTOH 14-3
bus
fail 24-16
segment no. 24-6
bus topology 26-7
busy
control 17-28
signal 17-31
C cable 17-2, 17-31, 23-1, 24-15
DeviceNet 25-4
cables and accessories A-5
calendar/clock
data write flag M8020 6-10
error 27-5
function processing A-2
setting using
a user program 15-7
WindLDR 15-7
carry (Cy) and borrow (Bw) M8003 6-9
carry or borrow signals 11-2
catch input 5-7
CC= and CC≥ instructions 7-14
CDISP 16-5
character
codes for character display unit 16-7
display 16-5
unit 16-7
clearing error codes 27-2
clock
adjusting using a user program 15-8
data adjust flag M8021 6-10
CMP< 10-1
CMP<= 10-1
CMP<> 10-1
CMP= 10-1
CMP> 10-1
CMP>= 10-1
CNT, CDP, and CUD instructions 7-11
comm port tab 17-3, 21-7
communication
enable button 2-2
fault 25-7
function 2-6
I/O terminals
SX5 A-4
SX5D 25-2
SX5L 26-3
parameters 17-32, 17-33
setting WindLDR 17-3
selector DIP switch 2-2
settings 2-6
compare
equal to 10-1
greater than 10-1
greater than or equal to 10-1
less than 10-1
less than or equal to 10-1
unequal to 10-1
computer link
1:1 communication 1-5
1:N communication 1-5
communication 22-1
system 1-5
connection status 25-7
connector pinout 17-2, 17-31, 23-1, 24-15
constant scan time 5-20
contact protection circuit for relay output 2-17
control
register 20-2
relay 20-10
control signal
option
DSR D8205/D8305 17-28
DTR D8206/D8306 17-29
RTS D8207/D8307 17-29
status D8204/D8304 17-27
statuses
RUN mode 17-27
STOP mode 17-28
conversion
linear 19-4
type 17-6, 17-15
convert
X to Y 19-2
Y to X 19-3
coordinate conversion instructions 19-1
counter
adding (up) counter 7-11
and shift register in master control circuit 7-26
comparison instructions 7-14
dual-pulse reversible counter 7-12
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

IDEC OpenNet series Specifications

General

Brand	IDEC
Model	OpenNet series
Category	Controller
Language	English