JUKI Sewing Machine - ChangNg the AuxLAry Feed OperatNg Mode <AuxLAry Feed Mode SelectOn

189 pages

Save Page as PDF

To Next Page

To Previous Page

–

3) Press STEP MODE SELECTION button

* When step mode is selected, shirring amount

range setting

is xed to – 4 to + 35.

4) Press ENTER button

(2) Changing the auxiliary feed operating mode <Auxiliary feed mode selection>

5) Press CANCEL button

1) Press MANUAL DETAILS SETTING button

Main Page

Default Chapter1
- Instruction Manual1
- Table of Contents2
Specifications7
- Specifications of the Machine Head7
- Specifications of the Control Box7
Configuration8
- Sewing Machine Main Unit8
- Operation Panel9
Installation10
- Caution at the Time of Set-Up10
- Assembling the Pedal Section of the Stand11
- Assembling the Table12
- Connecting the Power Cable13
- Installing the Sewing Machine Main Unit13
- Installing the Cover14
- Installing the Stopper for Tilt Prevention14
- Installing the Operation Panel14
- Connecting the Cords15
- Installing the Throat Plate Auxiliary Plate16
- Installing the Thread Guide Rod16
- Installing the Thread Stand17
- Assembling the Table for Work (Work Top Table)17
Preparation before Operation18
- Attaching the Needle18
- Threading the Needle-Thread18
- Winding the Bobbin Thread19
- Setting the Bobbin into the Bobbin Case19
- Attaching and Removing the Bobbin Case20
- Adjusting the Thread Tension20
- Adjusting the Thread Take-Up Spring20
- Adjusting the Stitch Guide20
Operation of the SEWING Machine (SEMI-Automatic Basic Volume)21
- Data Input Screen21
- Sewing Screen23
- Details Data Input Screen24
- Feed Amount26
- Basic Operation of the Sewing Machine27
- Basic Change of the Set Value31
- Creating the Pattern <Pattern Creation34
- Deleting the Pattern <Pattern Deletion35
Operation of the SEWING Machine (SEMI-Automatic Application Volume)37
- Correcting the Pattern37
- Copying the Pattern <Pattern Copy51
  - Pattern Copy in Semi-Automatic Mode <Copy to Semi-Automatic51
  - Pattern Copying from Semi-Automatic to Fully-Automatic <Copy to Fully-Automatic52
- Creating the New Pattern <New Pattern Creation53
- Using the Other Functions55
  - Directly Calling the Pattern from the Sewing Screen <Direct Pattern Selection55
  - Adjust the STEP SELECTION Button to the Shape of Sleeve <Measure Function55
Operation of the SEWING Machinre (Fully-Automatic Basic Volume)56
- Data Input Screen56
- Sewing Screen58
- Detailed Data Input Screen59
- Feed Amount61
- Basic Operation of the Sewing Machine62
- Changing the Basic Set Value65
- Creating the Pattern <Pattern Creation68
- Deleting the Pattern <Pattern Deletion70
Operation of the SEWING Machine (Fully-Automatic Application Volume)72
- Correcting the Pattern72
- Copying the Pattern <Pattern Copy90
  - Pattern Copy N the Fully-AutomatC <Copy to Fully-AutomatC90
  - Pattern Copy from Fully-AutomatC to Sem-AutomatC <Copy to Sem-AutomatC92
- Creating a New Pattern <New Pattern Creation93
- Using Other Functions95
  - DRectly CallNg the Pattern from SewNg Screen <DRect Pattern SelectOn95
  - Re-RegSterNg the Length between Steps <Measure FunctOn96
- Operation of the Sewing Machine (Manual Basic Volume)97
- Operation of the Sewing Machine (Manual Application Volume)104
  - Changing the Detailed Set Value104
- Using Counter111
  - Setting Procedure of the Counter111
  - Count-Up Releasing Procedure114
Registering and the Pattern to Direct Button and Releasing the Pattern from Direct Button114
- How to Register114
- How to Release115
- Register State at the Time of Your Purchase116
- Changing Sewing Mode116
- Changing Memory Switch Data117
Error Code List136
Using Communication Function140
- Handling Possible Data140
- Performing Communication by Using the Compactflash(TM)141
- Performing Communication by Using RS-232C143
- Take-In of the Data143
Information Function146
- Observing the Maintenance and Inspection Information146
- Inputting the Inspection Time148
- Releasing Procedure of the Warning149
- Observing the Production Control Information150
  - When DSplayNg from the NformatOn Screen150
  - When DSplayNg from the SewNg Screen151
- Performing Setting of the Production Control Information152
- Observing the Working Measurement Information155
Trial Sewing Function158
- Performing Trial Sewing158
Performing Key Lock160
Displaying Version Information162
Using Check Program163
- Displaying the Check Program Screen163
- Performing the Auxiliary Pedal Setting164
- Performing Checking of A/D Value of Auxiliary Pedal165
- Performing LCD Check165
- Performing Touch Panel Compensation166
- Performing the Input Signal Check168
- Performing the Output Signal Check170
Communication Screen of Maintenance Personnel Level172
- Data Which Are Possible to be Handledin Case of the Maintenance172
- Displaying Maintenance Personnel Level173
Information Screen of the Maintenance Personnel Level174
- Display of Error Record174
- Display of the Cumulative Working Information175
Maintenance176
- Replacing Procedure of Feed Belt176
- Changing the Amount of Alternate Vertical Movement of Walkingfoot and Presser Foot178
  - When MakNg Equal the Amount of Alternate VertCal Movement of WalkNg Foot and Presser Foot (When MakNg the Amount Equal to 1.5 MM)179
  - When MakNg 2.5 MM the Amount of Alternate VertCal Movement179
- Adjusting the Height of the Walking Foot and the Presser Foot180
  - AdjustNg the HeGht of WalkNg Foot180
  - AdjustNg the HeGht of Presser Foot180
- Adjusting the Needle and the Hook181
  - AdjustNg the HeGht of Needle Bar181
  - AdjustNg the Hook181
- Adjusting the Thread Trimmer182
- Greasing Parts184
Others185
- Troubles in Sewing and the Corrective Measures185
Drawing of the Table186
- Slant Table186
- Work Top Table187
- Edge Stopper a188
- Edge Stopper B189

JUKI Sewing Machine - ChangNg the AuxLAry Feed OperatNg Mode <AuxLAry Feed Mode SelectOn

Table of Contents

Related product manuals

JUKI Sewing Machine - ChangNg the AuxLAry Feed OperatNg Mode <AuxLAry Feed Mode SelectOn