JUKI Sewing Machine

To Next Page

To Previous Page

–

(4) Selecting left/right alternate sewing <Left/right alternate sewing selection>

(5) Performing sewing

Press LEFT/RIGHT ALTERNATE SEWING button

to select program changeover method (for

right sleeve and left sleeve).

1) Press READY key

2) Display changes over from data input screen

to sewing screen

Alternate sewing, right : Left/right alternate

sewing starting from the right sleeve

Alternate sewing, left : Left/right alternate

sewing starting from the left sleeve

Right sleeve only : Right sleeve sewing only

Left sleeve only : Left sleeve sewing only

Main Page

Default Chapter1
- Instruction Manual1
- Table of Contents2
Specifications7
- Specifications of the Machine Head7
- Specifications of the Control Box7
Configuration8
- Sewing Machine Main Unit8
- Operation Panel9
Installation10
- Caution at the Time of Set-Up10
- Assembling the Pedal Section of the Stand11
- Assembling the Table12
- Connecting the Power Cable13
- Installing the Sewing Machine Main Unit13
- Installing the Cover14
- Installing the Stopper for Tilt Prevention14
- Installing the Operation Panel14
- Connecting the Cords15
- Installing the Throat Plate Auxiliary Plate16
- Installing the Thread Guide Rod16
- Installing the Thread Stand17
- Assembling the Table for Work (Work Top Table)17
Preparation before Operation18
- Attaching the Needle18
- Threading the Needle-Thread18
- Winding the Bobbin Thread19
- Setting the Bobbin into the Bobbin Case19
- Attaching and Removing the Bobbin Case20
- Adjusting the Thread Tension20
- Adjusting the Thread Take-Up Spring20
- Adjusting the Stitch Guide20
Operation of the SEWING Machine (SEMI-Automatic Basic Volume)21
- Data Input Screen21
- Sewing Screen23
- Details Data Input Screen24
- Feed Amount26
- Basic Operation of the Sewing Machine27
- Basic Change of the Set Value31
- Creating the Pattern <Pattern Creation34
- Deleting the Pattern <Pattern Deletion35
Operation of the SEWING Machine (SEMI-Automatic Application Volume)37
- Correcting the Pattern37
- Copying the Pattern <Pattern Copy51
  - Pattern Copy in Semi-Automatic Mode <Copy to Semi-Automatic51
  - Pattern Copying from Semi-Automatic to Fully-Automatic <Copy to Fully-Automatic52
- Creating the New Pattern <New Pattern Creation53
- Using the Other Functions55
  - Directly Calling the Pattern from the Sewing Screen <Direct Pattern Selection55
  - Adjust the STEP SELECTION Button to the Shape of Sleeve <Measure Function55
Operation of the SEWING Machinre (Fully-Automatic Basic Volume)56
- Data Input Screen56
- Sewing Screen58
- Detailed Data Input Screen59
- Feed Amount61
- Basic Operation of the Sewing Machine62
- Changing the Basic Set Value65
- Creating the Pattern <Pattern Creation68
- Deleting the Pattern <Pattern Deletion70
Operation of the SEWING Machine (Fully-Automatic Application Volume)72
- Correcting the Pattern72
- Copying the Pattern <Pattern Copy90
  - Pattern Copy N the Fully-AutomatC <Copy to Fully-AutomatC90
  - Pattern Copy from Fully-AutomatC to Sem-AutomatC <Copy to Sem-AutomatC92
- Creating a New Pattern <New Pattern Creation93
- Using Other Functions95
  - DRectly CallNg the Pattern from SewNg Screen <DRect Pattern SelectOn95
  - Re-RegSterNg the Length between Steps <Measure FunctOn96
- Operation of the Sewing Machine (Manual Basic Volume)97
- Operation of the Sewing Machine (Manual Application Volume)104
  - Changing the Detailed Set Value104
- Using Counter111
  - Setting Procedure of the Counter111
  - Count-Up Releasing Procedure114
Registering and the Pattern to Direct Button and Releasing the Pattern from Direct Button114
- How to Register114
- How to Release115
- Register State at the Time of Your Purchase116
- Changing Sewing Mode116
- Changing Memory Switch Data117
Error Code List136
Using Communication Function140
- Handling Possible Data140
- Performing Communication by Using the Compactflash(TM)141
- Performing Communication by Using RS-232C143
- Take-In of the Data143
Information Function146
- Observing the Maintenance and Inspection Information146
- Inputting the Inspection Time148
- Releasing Procedure of the Warning149
- Observing the Production Control Information150
  - When DSplayNg from the NformatOn Screen150
  - When DSplayNg from the SewNg Screen151
- Performing Setting of the Production Control Information152
- Observing the Working Measurement Information155
Trial Sewing Function158
- Performing Trial Sewing158
Performing Key Lock160
Displaying Version Information162
Using Check Program163
- Displaying the Check Program Screen163
- Performing the Auxiliary Pedal Setting164
- Performing Checking of A/D Value of Auxiliary Pedal165
- Performing LCD Check165
- Performing Touch Panel Compensation166
- Performing the Input Signal Check168
- Performing the Output Signal Check170
Communication Screen of Maintenance Personnel Level172
- Data Which Are Possible to be Handledin Case of the Maintenance172
- Displaying Maintenance Personnel Level173
Information Screen of the Maintenance Personnel Level174
- Display of Error Record174
- Display of the Cumulative Working Information175
Maintenance176
- Replacing Procedure of Feed Belt176
- Changing the Amount of Alternate Vertical Movement of Walkingfoot and Presser Foot178
  - When MakNg Equal the Amount of Alternate VertCal Movement of WalkNg Foot and Presser Foot (When MakNg the Amount Equal to 1.5 MM)179
  - When MakNg 2.5 MM the Amount of Alternate VertCal Movement179
- Adjusting the Height of the Walking Foot and the Presser Foot180
  - AdjustNg the HeGht of WalkNg Foot180
  - AdjustNg the HeGht of Presser Foot180
- Adjusting the Needle and the Hook181
  - AdjustNg the HeGht of Needle Bar181
  - AdjustNg the Hook181
- Adjusting the Thread Trimmer182
- Greasing Parts184
Others185
- Troubles in Sewing and the Corrective Measures185
Drawing of the Table186
- Slant Table186
- Work Top Table187
- Edge Stopper a188
- Edge Stopper B189

JUKI Sewing Machine - Page 63

Table of Contents

Related product manuals