Keithley 2600B

Series 2600B
System SourceMeter® Instrument Reference Manual Section 5: Intro
duction to TSP operation
2600BS-901-01 Rev. C / August 2016 5-17
Triggering
The triggering commands allow you to set the conditions that the instrument uses to determine when
measurements are captured. See Sweep operation (on page 3-20
) for details on sweeping.
The digio and tsplink commands are not available on the Models 2604B, 2614B, and 2634B
digio.trigger[N].assert() (on page 7-55)
digio.trigger[N].clear() (on page 7-55)
digio.trigger[N].EVENT_ID (on page 7-56)
digio.trigger[N].mode (on page 7-56)
digio.trigger[N].overrun (on page 7-58)
digio.trigger[N].pulsewidth (on page 7-58)
digio.trigger[N].release() (on page 7-59)
digio.trigger[N].reset() (on page 7-60)
digio.trigger[N].stimulus (on page 7-61)
digio.trigger[N].wait() (on page 7-63)
display.trigger.clear() (on page 7-86)
display.trigger.EVENT_ID (on page 7-86)
display.trigger.overrun (on page 7-87)
display.trigger.wait() (on page 7-87)
lan.trigger[N].assert() (on page 7-140)
lan.trigger[N].clear() (on page 7-141)
lan.trigger[N].connect() (on page 7-142)
lan.trigger[N].connected (on page 7-142)
lan.trigger[N].disconnect() (on page 7-143)
lan.trigger[N].EVENT_ID (on page 7-144)
lan.trigger[N].ipaddress (on page 7-144)
lan.trigger[N].mode (on page 7-145)
lan.trigger[N].overrun (on page 7-146)
lan.trigger[N].protocol (on page 7-147)
lan.trigger[N].pseudostate (on page 7-147)
lan.trigger[N].stimulus (on page 7-148)
lan.trigger[N].wait() (on page 7-150)
smuX.trigger.arm.count (on page 7-250)
smuX.trigger.arm.set() (on page 7-250)
smuX.trigger.arm.stimulus (on page 7-251)
smuX.trigger.ARMED_EVENT_ID (on page 7-253)
smuX.trigger.autoclear (on page 7-253)
smuX.trigger.count (on page 7-254)
smuX.trigger.endpulse.action (on page 7-254)
smuX.trigger.endpulse.set() (on page 7-255)
smuX.trigger.endpulse.stimulus (on page 7-256)
smuX.trigger.endsweep.action (on page 7-258)
smuX.trigger.IDLE_EVENT_ID (on page 7-258)
smuX.trigger.initiate() (on page 7-259)
smuX.trigger.measure.action (on page 7-260)
smuX.trigger.measure.set() (on page 7-261)
smuX.trigger.measure.stimulus (on page 7-261)
smuX.trigger.measure.Y() (on page 7-264)
smuX.trigger.MEASURE_COMPLETE_EVENT_ID (on page 7-265)
smuX.trigger.PULSE_COMPLETE_EVENT_ID (on page 7-265)
smuX.trigger.source.action (on page 7-266)
smuX.trigger.source.limitY (on page 7-267)
smuX.trigger.source.linearY() (on page 7-268)
smuX.trigger.source.listY() (on page 7-269)
smuX.trigger.source.logY() (on page 7-270)