Keysight Technologies E5260 Series

To Previous Page

This information is subject to change without notice.

Edition 6, September 2015

*E5260-90000*

E5260-90000

www.keysight.com

Main Page

Table of Contents17
Getting Started23
Introduction31
Keysight E5260/E5270 Series33
Front View34
Rear View37
Measurement Modules38
Compliance38
GNDU - Ground Unit39
E5280B Precision HPSMU40
E5281B Precision MPSMU43
E5287A Atto Level HRSMU46
E5290A High Speed HPSMU50
E5291A High Speed MPSMU53
Accessories and Options56
Installation61
Requirements64
Power Requirements64
Operating Environment64
Storaging/Shipping Environment64
Installation Requirements65
Power Cable65
Inspection and Installation68
To Inspect the Keysight E5260/E5270 and Accessories68
To Check the Keysight E5260/E5270 Operation68
To Execute Diagnostics and Self-Calibration69
To Remove or Install Plug-In Module70
Installing Accessories73
To Connect 16442B Test Fixture75
To Connect Connector Plate77
To Connect ASU79
To Connect GNDU Adapter83
Mounting Connectors84
To Make an Interlock Circuit86
To Connect the GNDU Output89
To Connect the SMU Output90
Connecting Measurement Devices95
Using Test Fixture96
Using Connector Plate98
Maintenance103
Calibration103
Cleaning103
Self-Test and Diagnostics104
Front Panel Reference105
Display and Front Panel Keys107
Display Images107
Front Panel Key Locations109
Channel Status Area110
Setup Data Area111
Measurement Data Area112
Status Data Area113
Front Panel Key Details114
Measure Key Group115
Output Key Group118
Edit Key Group121
Setup Menus122
Setup Menu122
Calibration and Test Menu129
Measurement Range Setup Menu135
Output Range Setup Menu136
Front Panel Operations137
Available Functions139
Setting up Keysight E5260/E5270140
To Set Line Frequency141
To Initialize Keysight E5260/E5270141
To Set Beeper141
To Apply Default Value141
To Select Monitor Items142
To Perform Self-Test143
To Perform Self-Calibration144
To Perform Diagnostics145
To Set Auto-Calibration147
To Set ADC Zero Function147
To Read Error Message148
To Display Firmware Revision148
To Display Module Information149
To Display Module Serial Number149
To Set GPIB Address150
To Set Remote Display Mode150
To Return to Local Mode150
Applying Source Output151
To Apply DC Current/Voltage152
To Set Output/Compliance Value153
To Set Source Output to Zero154
To Set Output Range154
To Use Series Resistor155
To Use Filter155
To Switch ASU Internal Connection156
Making Measurement157
To Measure DC Current/Voltage158
To Abort Measurement159
To Select Measurement Item159
To Select Measurement Range160
To Set A/D Converter161
To Set Wait Time163
To Set Data Display Format164
Function Details165
Measurement Mode167
Measurement Mode in Local Condition167
Measurement Mode in Remote Condition168
Ranging Mode169
To Set the Ranging Mode169
Auto Ranging170
Limited Auto Ranging171
Fixed Range171
Compliance Range171
Enhanced Auto Ranging for Current Measurement172
Compliance173
Polarity and Output Area173
Power Compliance175
To Set Compliance177
SMU Pulse179
To Set Pulse Output179
Measurement Time180
Integration Time180
Overhead Time182
To Specify Source Output Time182
Wait Time183
Atto Sense and Switch Unit184
Filter186
Series Resistor187
Interlock Function188
Auto Power off Function189
Initial Settings190
If You Have a Problem195
When You Install the E5260/E5270197
If the E5260/E5270 Cannot be Powered on197
To Simplify the Connections197
When You Make a Measurement198
If Leaving Connections Damages Devices after Measurement198
If Measured Value Oscillates When Measuring High-Frequency Devices199
If Measured Value Oscillates When Measuring Negative Resistance200
If Noise Affects the Measured Values201
If Measured Voltage Has some Error When Forcing a Large Current202
If Large Current Causes High Temperature (Thermal Drift)202
If Measurement Takes more Time than Specified202
If Measurement Damages the Device under Test203
Channel Status Code204
Error Codes205
Operation Error205

Keysight Technologies E5260 Series

Table of Contents

Other manuals for Keysight Technologies E5260 Series

Related product manuals