Krone EasyCut B 1000 CV - Angular Gearbox Oil Level and Change (Top Part)

Maintenance - Gearbox
185
Pos: 90.1 /Überschri ften/Überschrif ten 2/U-Z/Winkelgetr iebe @ 0\mod_11970059182 99_78.docx @ 15435 @ 2 @ 1
18.3 Angular gearbox
Pos: 90.2 /Abkürzungen / CR-Ausführung @ 194\ mod_1383299073254_78. docx @ 1647987 @ @ 1
CR design
Pos: 90.3 /Überschri ften/Überschrif ten 3/K-O/Oberteil @ 10\ mod_1221639445993_78. docx @ 135690 @ 3 @ 1
18.3.1 Top part
Pos: 90.4 /BA/War tung/Hinweis Ölstandskontr olle in Arbeitsste llung und in waagerecht er Stellung der Maschine vornehmen @ 194\mod_138355 4973754_78.doc x @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 90.5 /BA/War tung/Ölkontrolle_Wec hsel/Mähwerke/Bild W inkelgetriebe Obertei l CRI @ 10\mod_122155583146 3_78.docx @ 135326 @ @ 1
EC-210-0
2
1
Figure 117
Pos: 90.6 /BA/War tung/Ölkontrolle_Wec hsel/Ölwechsel / Ölkon trolle:Legende zu Grafi k Kontrollschraub e / Einfüllschraube @ 194\ mod_1383298407773_ 78.docx @ 1647929 @ @ 1
1) Inspection screw / control hole 2) Filler plug / oil filling hole
Pos: 90.7 /BA/War tung/Ölkontrolle_Wec hsel/Ölqualität /Öl menge: siehe Kapitel Techni sche Daten @ 134\mod_135 0483480921_78.doc x @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 90.8 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle / Öl wechsel Intervall: si ehe Kapitel Wartung „W artungstabelle“ @ 134\ mod_1350483605921_78. docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 90.9 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle NE U über Kontrollschraube @ 140\mod_135514175368 0_78.docx @ 1244582 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Screw out filler plug.
• Top up oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 90.10 /BA/W artung/Ölkontrolle_Wec hsel/Ölwechsel NE U Kontrollschraube, Einf üllschraube Öl absauge n @ 207\mod_138677359965 1_78.docx @ 1716145 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out inspection screw and filler plug and drain the oil.
• Top up new oil via oil filling hole until the control hole is reached.
• Screw in inspection screw and filler plug and tighten them securely.
Pos: 90.11 /BA/W artung/Ölkontrolle_Wec hsel/Hinweis - Altöl ordn ungsgemäß entsorgen @ 0\ mod_1197008117002_78. docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 91 /Layout Modu le /---------------Seitenumbruch---------------- @ 0\mod_11961753112 26_0.docx @ 4165 @ @ 1