Krone EasyCut B 1000 CV - Raise;Lower Front Mowing Unit Control

KRONE ISOBUS CCI 100 Terminal / manual mode
64
Pos: 61.39.3.1 /Übersc hriften/Überschr iften 2/F-J/ Grundbild Frontmähwerk heben/se nken @ 93\mod_1327385 514150_78.docx @ 787407 @ 2 @ 1
9.2 'Raise/Lower front mowing unit' basic dialogue
Pos: 61.39.3.2 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- Swadro/Swadro 1400Gef ahr Schnellstop (2014-1 0-07 11:55:57) @ 56\mod_12 95362873734_78.doc x @ 542364 @ @ 1
DANGER! - Before swivelling the machine, ensure that nobody is within the swivel
range.
Effect: Danger to life or serious injuries.
• Instruct persons to leave the danger zone.
• If required, switch off the machine immediately.
• If there is an imminent danger, press the function key for to stop all functions which
are currently being performed.
Pos: 61.39.3.3 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senkenGrundbi ld Frontmähwerk senken/ heben Bild (2014-10- 07 13:18:33) @ 93\mod_13273 85383243_78.doc x @ 787352 @ @ 1
Fig. 36
Pos: 61.39.3.4 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senken/Ar beiten nur mit Frontmäh werk @ 93\mod_132738618635 3_78.docx @ 787547 @ @ 1
The front mowing unit alone can be used for partial mowing, to mow small parcels of crop or
narrow sections in open fields. To this end the lateral mowing units must be in transport position
and locked.
Pos: 61.39.3.5 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senken/Grund bild Frontmähwerk hebe n/senken Einführte xt @ 93\mod_13273856953 61_78.docx @ 787465 @ @ 1
The 'Raise/Lower front mowing unit' basic dialogue only appears when the front mowing unit is
attached and the lateral mowing units are in transport position or above the headland position.
Pos: 61.39.3.6 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senken/F9 Auf rufen Grundbild Fron tmähwerk heben/senken @ 93\mod_1327390678666 _78.docx @ 787630 @ @ 1
Calling the 'Raise/Lower front mowing unit' basic dialogue
The 'Raise/Lower front mowing unit' basic dialogue is indicated on the terminal via the
symbol.
Press the function key for
until the symbol appears on the display.
Pos: 61.39.3.7 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senkenFront mähwerk senken (2014-10- 07 14:28:37) @ 93\mod_1 327385898750_78. docx @ 787492 @ 3 @ 1
9.2.1 Lower front mowing unit
• Pressing the function key for
once lowers the front mowing unit to the working position.
Pos: 61.39.3.8 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Frontmäh werk heben/senkenFront mähwerk heben (2014- 10-07 14:30:19) @ 93\mod_13 27386039772_78.doc x @ 787519 @ 3 @ 1
9.2.2 Raise front mowing unit
• Pressing the function key for
once raises the front mowing unit to the transport
position.
Pos: 61.39.3.9 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.doc x @ 4165 @ @ 1