Krone EasyCut B 1000 CV - Load-Sensing Connection; Operating the Machine Without LS (Load-Sensing Connection); Operating the Machine Via LS (Load-Sensing Connection)

Start-up
39
Pos: 59.11.1 /Überschr iften/Überschri ften 2/K-O/Load-Sensi ng-Anschluss @ 1\mod _1201241225401_78.doc x @ 51955 @ 2 @ 1
7.3 Load-sensing connection
Pos: 59.11.2 /BA/War tung/Load-Sensing/Ea syCut B 1000/Bild Load-Se nsing Anschluss EC B 1000 @ 98\ mod_1329405519207_78. docx @ 878790 @ @ 1
Fig. 14
Pos: 59.11.3 /BA/War tung/Load-Sensing/ Großpackenpresse/ Load-Sensing-Ansch luss BigPack @ 24\mod_1241 604498659_78.docx @ 2 46628 @ @ 1
The Comfort hydraulic system is load-sensing-capable.
The oil supply comes through the Power-Beyond system of the tractor hydraulics for use of the
load-sensing system (further information can be obtained from the operating instructions
provided by the manufacturer of the tractor).
Pos: 59.11.4 /BA/W artung/Load-Sensing/Ea syCut B 1000/Anpassen de s Hydrauliksystem s EasyCut B 1000 @ 98\mod_132940 6670739_78.doc x @ 878876 @ @ 1
Adapt the Comfort hydraulic system of the machine to the tractor. The hydraulic system is
designed for continuous circulation. The adjustment is made by adjusting the hydraulic system
screw on the control valve block of the machine. The control valve block is at the front and in
the middle under the three-point block.
Note
The adjustment depends on the hydraulic system of the tractor and must be made while the
machine is depressurised!
Pos: 59.11.5 /Überschr iften/Überschri ften 3/A-E/B/Betr ieb der Maschine ohne LS (Load- Sensing-Anschluss) @ 91\mod_1326699351886_ 78.docx @ 780162 @ 3 @ 1
7.3.1 Operating the Machine without LS (Load-Sensing Connection)
Pos: 59.11.6 /BA/War tung/Load-Sensing/Sy stemschraube (1) ganz herausdrehen @ 63\mod_1299 739012796_78.doc x @ 575371 @ @ 1
Unscrew the system screw (1) as far as it will go for:
• Tractor with an open (constant-current) hydraulic system (for additional information, please
refer to the tractor manufacturer's operating instructions)
• Tractors with LS pump and non-activated load-sensing system
Pos: 59.11.7 /BA/War tung/Load-Sensing/ Hinweis Einstellung is t vom Werk aus gegeben @ 63\mod_ 1299738968068_78.doc x @ 575344 @ @ 1
Note
This adjustment is set when the unit leaves the factory.
Pos: 59.11.8 /Überschr iften/Überschri ften 3/A-E/B/Betr ieb der Maschine über LS (Load- Sensing-Anschluss) @ 91\mod_1326699464848 _78.docx @ 780190 @ 3 @ 1
7.3.2 Operating the Machine via LS (Load-Sensing Connection)
Pos: 59.11.9 /BA/War tung/Load-Sensing/Sy stemschraube (1) ganz hereindrehen @ 63\mod_129 9738923981_78.doc x @ 575317 @ @ 1
Screw the system screw (1) as far as it will go for:
• Tractors with closed (constant pressure or load sensing) Hydraulic system (For more
information, please refer to the tractor manufacturer's operating instructions)
• Tractors with LS pump and message line that is connected
Pos: 59.12 /Layout Module /---------------Seitenumbruc h---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1