Maintenance - Gearbox
186
Pos: 92.1 /Überschri ften/Überschrif ten 2/U-Z/Winkelgetr iebe @ 0\mod_11970059182 99_78.docx @ 15435 @ 2 @ 1
18.4 Angular gearbox
Pos: 92.2 /Abkürzungen / CR-Ausführung @ 194\ mod_1383299073254_78. docx @ 1647987 @ @ 1
CR design
Pos: 92.3 /Überschri ften/Überschrif ten 3/U-Z/Unterteil @ 10\ mod_1221640227712_78. docx @ 135712 @ 3 @ 1
18.4.1 Bottom part
Pos: 92.4 /BA/War tung/Hinweis Ölstandskontr olle in Arbeitsste llung und in waagerecht er Stellung der Maschine vornehmen @ 194\mod_138355 4973754_78.doc x @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 92.5 /BA/War tung/Ölkontrolle_Wec hsel/Mähwerke/Bild W inkelgetriebe CRI @ 0\mod_11 97013688111_78.doc x @ 15844 @ @ 1
EC-189-0
1
2
Fig. 118:
Pos: 92.6 /BA/War tung/Ölkontrolle_Wec hsel/Ölwechsel / Ölkon trolle:Legende zu Grafi k Kontrollschraub e / Ablassschraube @ 194\mo d_1383299451132_78.doc x @ 1648045 @ @ 1
1) Inspection screw / control hole 2) Drain plug
Pos: 92.7 /BA/War tung/Ölkontrolle_Wec hsel/Ölqualität /Öl menge: siehe Kapitel Techni sche Daten @ 134\mod_135 0483480921_78.doc x @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 92.8 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle / Öl wechsel Intervall: si ehe Kapitel Wartung „W artungstabelle“ @ 134\ mod_1350483605921_78. docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 92.9 /BA/War tung/Ölkontrolle_Wec hsel/Ölkontrolle NE U über Kontrollschraube ohne E infüllschraube @ 158\ mod_1364483633589_7 8.docx @ 1391741 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Top up oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 92.10 /BA/W artung/Ölkontrolle_Wec hsel/Ölwechsel NE U ohne Einfüllschraube @ 158\m od_1364483760090_78.d ocx @ 1391770 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out oil drain plug and drain the oil.
• Screw out inspection screw.
• Screw in oil drain plug and tighten it securely.
• Top up new oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 92.11 /BA/W artung/Ölkontrolle_Wec hsel/Hinweis - Altöl ordn ungsgemäß entsorgen @ 0\ mod_1197008117002_78. docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 93 /Layout Modu le /---------------Seitenumbruch---------------- @ 0\mod_11961753112 26_0.docx @ 4165 @ @ 1
To Next Page
Loading...
