Krone EasyCut B 1000 CV - Increasing; Decreasing the Overcut; Increasing; Decreasing the Lateral Displacement

KRONE ISOBUS CCI 100 Terminal / automatic mode
89
Pos: 61.43.3.20 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Automatikb etriebÜbersc hnitt vergrößern / verk leinern Auto (2014-10-08 1 1:43:45) @ 93\mod_132 7482364843_78.doc x @ 789905 @ 3 @ 1
10.2.9 Increasing / Decreasing the overcut
The overcut allows the working width of the lateral mowing units to be adjusted in relation to the
front mowing unit such that no crop sections are left standing when driving straight ahead /
round bends.
Two different values can be stored for the overcut at the same time (e.g. for driving straight
ahead and in a curve).
• Pressing the function key for
Auto
causes the first of the stored values for the lateral
mowing units to be applied.
• Pressing the function key for
Auto
again causes the second of the stored values for the
lateral mowing units to be applied.
Pos: 61.43.3.21 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Automatikb etriebÜbersc hnitt vergrößern durc h Touch (2014-10-08 12:07:0 5) @ 118\mod_13415664594 96_78.docx @ 1025801 @ @ 1
An input mask opens by touching the number in front of the symbol ( ) in the display and
the overcut can be increased or reduced continuously during operation.
Pos: 61.43.3.22 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Automatikb etriebWerte für Überschnitt ändern ( 2014-10-08 12:13:02) @ 93\ mod_1327488210728_78. docx @ 790050 @ @ 1
Changing the overcut values
• Pressing the function key for
Auto
and keeping it pressed for approx. 2 sec calls up the
overcut menu 1-1.
Note
For further information, see Settings chapter 'Menu 1-1 Overcut'
Pos: 61.43.3.23 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Automatikb etriebBreiten verschiebung vergr ößern / verkleinern Auto ( 2014-10-08 12:52:16) @ 93\mod_1327484586702_78. docx @ 789932 @ 3 @ 1
10.2.10 Increasing / Decreasing the lateral displacement
The lateral displacement function allows both lateral mowing units to be shifted to the right or
left at the same time (for mowing in one direction, then the other), so that when mowing on a
slope no crop sections remain standing.
Pressing the function key for
Auto
causes the two lateral mowing units to shift the specified
distance to the right.
Pressing the function key for
Auto
again causes the two lateral mowing units to shift the
specified distance to the left.
Pos: 61.43.3.24 /BA/ Info-Center/CCI -ISOBUS-Terminal/CCI- EasyCut/EasyCut B 1000/ Grundbild Automatikb etriebWerte für Breitenverschiebung ä ndern (2014-10-08 13:1 3:37) @ 93\mod_1327489 589131_78.doc x @ 790077 @ @ 1
Changing the lateral displacement values
• Pressing the function key for
Auto
and keeping it pressed for approx. 2 sec calls up the
lateral displacement menu 1-2.
Note
For further information, see Settings chapter 'Menu 1-2 Lateral displacement'
Pos: 61.44 /Layout Module /---------------Seitenumbruc h---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1