Loop Telecom IP6610

To Next Page

To Previous Page

Chapter 13 Remote Bridge Setup

The IP 6610 set up procedure for the first unit is now complete. Repeat these instructions to set up the

other IP 6610 unit in this application.

Main Page

Default Chapter3
- Table of Contents3
1 Product Description10
- Description10
- Applications11
- Figure 1-2 Application Illustration11
- Figure 1-3 Mobile ATM Solution11
- Figure 1-4 Ethernet to Data Transmission Solution11
- Specifications13
- Site Selection16
- Mechanical Installation16
  - Desktop Installation16
- Front Panel Console Port and Leds18
  - IP 6610 DTE Front Panel and Rear Panel18
- Console18
- Figure 2-1 Loop-IP 6610 Front Panel (Single Ethernet)18
- Figure 2-2 Loop-IP6610 DTE Front Panel (Four Ethernet)18
- Figure 2-3 Loop-IP6610 DTE Front Panel (Single Ethernet)18
- Figure 2-4 Loop-IP 6610 DTE Rear Panel (EIA 530) with AC Power (1 Port)19
- Figure 2-5 Loop-IP 6610 DTE Rear Panel (EIA 530) with DC Power (1 Port)19
- Figure 2-6 Loop-IP 6610 DTE Rear Panel (EIA 530) with AC Power (4 Port)19
- Figure 2-7 Loop-IP 6610 DTE Rear Panel (EIA 530) with DC Power (4 Port)19
- Rear Panel Connectors and Switch20
2 Loop-Ip6610 Installation29
- Main Board Jumper Selection29
3 Operation30
- Quick Start for Loop-IP6610 Router30
- Power on30
- Self-Test30
- Usinga Terminal30
- Review and Default Settings30
- Wan1 Timeslot Map Setup30
- System Operation31
  - Date31
  - Console Port31
  - Login and Logout31
- Configuration31
- Line Configuration31
  - E1/DS1 Line Configuration31
  - Table 3-1 Console Port Default Setting31
  - Table 3-2 E1 Line Default Setting31
  - Table 3-3 DS1 Line Default Setting32
  - DTE Line Configuration34
- Reports34
- Table 3-4 DTE Line Default Setting34
- Table 3-5 Performance Parameter List - E134
- Led Operation35
- Table 3-6 Performance Parameter List - DS135
- Table 3-7 Front Panel LED Indication35
- Alarms and Reports36
  - Alarms36
  - Table 3-8 E1 Alarm Type Table36
  - Reports37
- Unit Alarm Code Filters38
- Embedded Snmp Agent38
- Code Filter38
- Rip1 and Rip2 Routing Protocols39
- Figure 3-1 SNMP Connection39
- Verifying Loop-IP 6610 Operations40
  - Independent Test40
  - Substitution40
  - Using Loopback Plugs40
  - Using the Bert Test Set41
4 Maintenance42
- Self-Test42
- Diagnostics42
- Loopbacks42
- Test Pattern44
  - 3-In-24 Pattern44
  - 1-In-8 Pattern44
5 Loop-Ip6610 Setup45
- Setting up the IP661045
- Login, Password, Save, Logout, and Reset46
- Wan1 Setup47
- Table 5-2 WAN1 Admin Commands -E148
- Table 5-3 WAN1 Admin Commands -DS148
- Lan1 Setup49
- Table 5-4 LAN1 Admin Commands49
6 Dhcp Server Setup50
- Overview50
- Figure 6-1 DHCP Application50
- Dhcp Setup Commands51
- Table 6-1 DHCP Setup Commands51
- Step by Step Setup Instructions52
- Dhcp Relay Setup55
7 Frame Relay Setup57
- Overview57
- Figure 7-1 Frame Relay Application57
- Frame Relay Setup Commands58
- Table 7-1 Frame Relay Setup Commands58
- Step by Step Setup Instructions59
8 Ip Routing Setup61
- Overview61
- Routing Admin Commands61
- Figure 8-1 IP Routing Setup61
- Table 8-1 Routing Admin Commands61
- Step by Step Setup Instructions62
9 Ip Routing with Network Address Translation66
- Overview66
- Routing Admin Commands66
- Figure 9-1 Setting up IP Routing with Network Address Translation66
- Step by Step Setup Instructions67
10 Packet Filtering Setup70
- Overview70
- Step by Step Setup Instructions71
11 Port Forwarding - Virtual Service74
- Overview74
- Port Forwarding - Virtual Service Commands74
- Figure 11-1 Port Forwarding - Virtual Service Application74
- Table 11-1 Port Forwarding - Virtual Service Commands74
- Step by Step Setup Instructions75
12 Qos77
- Overview77
- Policy Syntax77
- Step by Step Setup Instructions78
- Figure 12-1 Qos Application79
13 Remote Bridge Setup81
- Overview81
- Figure 1-1 Loop-IP 661081
- Figure 13-1 Remote Bridge Mode Setup81
- Bridge Admin Commands82
- Step by Step Setup Instructions82
- Table 13-1 Bridge Admin Commands82
14 Snmp Configuration Setup86
- Overview86
- Network Management Admin Commands86
- Step by Step Instructions86
- Table 14-1 Network Management Admin Commands86
15 Stp/Rstp Setup89
- Overview89
- Figure 15-1 Normal STP Link89
- Figure 15-2 Restored STP Link90
- Stp/Rstp Setup Commands91
- Table 15-1 STP/RSTP Setup Commands91
- Step by Step Setup Instructions92
16 Vlan96
- Overview96
- Figure 16-1 VLAN Application #196
- Vlan and Mac Tables97
- Vlan Commands and Setup Instructions99
17 Vlan Stacking (Q-In-Q) Setup106
- Overview106
- Vlan Stacking106
- Figure 17-1 Transparently Conveying VLAN-Enabled Customer Traffic106
- Figure 17-2 802.1Q Encapsulation106
- Figure 17-3 802.1Ad (Qinq) Encapsulation106
- Definitions107
- Table 17-1 Egress Process107
- Vlan Stacking Commands and Setup Instructions108
- Table 17-2 VLAN Stacking Unit Commands108
- Setup Example109
18 Ppp Authentication110
- Overview110
- Figure 18-1 PPP Application110
19 Modem Dial-Up112
- Overview112
- Figure 19-1 at Modem Application112
20 Setting up Firmware/Configuration Up/Download with Tftp Server114
- Overview114
- Step by Step Setup Instructions117
21 Appendix A: Operation Commands120
- Command Line Interface Configuration120
- Table 21-1 Unit Command Parameters121
- Table 21-2 E1 Command Lines133
- Table 21-3 DS1 Command Lines135
- Table 21-4 DTE Command Lines137
- Table 21-5 DCE Command Lines138
- Command Usage139
22 Appendix B Converting a Subnet Mask to Binary Code183
23 Appendix C - Router Activation Procedure185
- Figure 23-1 VT-100 Terminal185
24 Appendix D - Application Note187
- Layer 3 Media Converter Application187
- Figure 24-1 Layer 3 Media Converter Application187
- Mobile Atm Application188
- Figure 24-2 Mobil ATM Application with Fixed IP188
- Figure 24-3 Mobil ATM Application with Dynamic IP189

Loop Telecom IP6610 - Page 85

Table of Contents

Related product manuals