Magtrol DSP7000 User Manual

iii
Date Edition Change Section(s)
03/09/13 2 nd Edition Din1,#, Din2,# command updated.
TAC1,#, TAC2,# command updated.
7.4.4
03/09/13 2 nd Edition Drawing updated 3.2.4.1, 3.2.5.1,
3.2.7.1, 3.2.8.1,
3.2.9.1, 3.2.10.1
03/09/13 2 nd Edition Note updated with correct section number for the Torque
Filter information.
3.2.1
03/09/13 2 nd Edition New features updated. 1.2
02/20/13 1st Edition - rev. Q One “x” added to the OD1, OD2 command to show a
return of 6 speed digits.
7.4.2
02/13/13 1st Edition - rev. P Section 6.8 How to Set the TM/TF Invert Flag added.
DINØ, DIN1 changed to DIRØ, DIR1 in the note section.
6.8
7.5
01/31/13 1st Edition - rev. O Step added to the setup instructions. 4.3.1
01/25/13 1st Edition - rev. N TMV1,# and TMV2,# command added.
A note was added to the DSP6001 Mode instructions.
7.4.7
7.5
01/04/13 1st Edition - rev. M F1,xx.xx and F2,xx.xx command function and denition
updated.
7.4.5
11/14/12 1st Edition - rev. L OS,# miscellaneous command added.
Calibration of Frequency added to the calibration
procedures.
7.4.7
9.3.4
10/26/12 1st Edition - rev. K The Supply 1/Supply 2 pin descriptions updated. 2.4.1
05/29/12 1st Edition - rev. J Power Supply connector description changed to include
HD 825 dynamometers.
1.3
04/25/12 1st Edition - rev. I Brake fuse changed to 1.25 Amps.
Congure Output Binary table descriptions updated.
1.3
7.2.2
03/14/12 1st Edition - rev. H OV,# command updated for both channels. 7.4.7
01/12/12 1st Edition - rev. G Section 6.6 How to Set Preload Control and section 6.7
How to Set and Reset Tare Function was added.
The ALC,# Alarm Command was added to section 7.4.1.
The TS1, TS2, TR1 and TR2 Commands were added to
section 7.4.7.
6.6, 6.7
7.4.1, 7.4.7
01/09/12 1st Edition - rev. F Driver and Tera Term location changed to Magtrol Manual
CD
7.1.1, 7.1.2, 8.4.2
12/27/11 1st Edition - rev. E USB Driver setup updated. 7.1.1, 7.1.2
12/13/11 1st Edition - rev D “Open or 8 Volts” was changed to “Open collector” for pin
9 in section 8.1.2. Function was changed for ALR1,# and
ALR2,# in section 7.4.1.
8.1.2, 7.4.1
12/06/11 1st Edition - rev C RPM vs PPR Chart added 3.4
12/02/11/ 1st Edition - rev B STAT command was updated in section 7.4.7 to include
ramp down, ramp up, and mode input. The OP command
was added in section 7.4.8.
7.4.7, 7.4.8
11/14/11 1st Edition - rev A Contact Rating changed from 1 amp, 24 VDC to 24 VDC,
1 amp max.
5.1.1, 8.1.2

Magtrol DSP7000 Specifications

General

Brand	Magtrol
Model	DSP7000
Category	Controller
Language	English