QUANTA Rackgo X Series F03A

To Next Page

To Previous Page

CHECKPOINTS BIOS

3-57

OEM-Reserved Checkpoint Ranges

Table 46: OEM Reserved Checkpoint Ranges

STATUS CODE DESCRIPTION

0x05 OEM SEC initialization before microcode loading

0x0A OEM SEC initialization after microcode loading

0x1D – 0x2A OEM pre-memory initialization codes

0x3F – 0x4E OEM PEI post memory initialization codes

0x80 – 0x8F OEM DXE initialization codes

0xC0 – 0xCF OEM BDS initialization codes

Main Page

Table of Contents3
Precautionary Measures11
Intended Application Uses12
Site Selection12
Equipment Handling Practices13
Power and Electrical Warnings13
System Access Warnings13
Rack Mount Warnings14
Cooling and Airflow15
Laser Peripherals or Devices15
General Information16
Structure of this Guide18
About the System19
Introduction20
A Tour of the System22
- System Overview22
- LED Definitions26
Safety Measures30
Sled Tray31
- Releasing the Sled Tray31
- Securing a Sled Tray31
Air Duct33
- Removing an Air Duct33
- Installing an Air Duct34
Fan Module35
- Removing a Fan Module35
- Installing a Fan Module38
Midplane Board41
- Removing the Midplane41
- Installing the Midplane43
Dimms45
- Banks and Channels45
- Memory Population Rules46
- Removing a Memory Module47
- Installing a Memory Module47
Intelligent Battery Backup Unit (Optional)49
- Removing an Ibbu49
- Installing an Ibbu50
Processor Heat Sinks52
- Removing a Processor Heat Sink52
- Installing a Processor Heat Sink53
Processors55
- Removing a Processor55
- Installing a Processor56
Interposer Board58
- Removing the Interposer Board58
- Installing the Interposer Board58
Mezzanine Board (Optional)60
- Removing the Mezzanine Board60
- Installing the Mezzanine Board61
Mainboard63
- Removing a Mainboard63
- Installing a Mainboard64
Hard Disk Drive Tray65
- Removing the HDD Tray65
- Installing the HDD Tray66
  - Removing Hard Disk Drives66
  - Installing Hard Disk Drives67
BIOS Setup Utility70
- Operation70
- Setup Page Layout70
- Entering BIOS Setup70
- Keyboard Commands71
- Menu Selection Bar72
- Server Platform Setup Utility Screens73
- Main Screen73
- Advanced Screen74
- Chipset Screen90
- Boot Screen100
  - Network Device BBS Priorities102
  - CSM Parameters103
- Security Screen104
- Loading BIOS Defaults110
BIOS Update Utility111
- AFULNX: V2.39111
- ME Region Update111
- BIOS Setting Utility112
- BIOS Recovery112
- BIOS Revision113
- Clear CMOS116
- Clear Password117
Server Management118
- Console Redirection118
- Network BIOS Support120
  - PXE Boot120
- Checkpoints120
Introduction128
KVM Client Hardware Requirements128
Remote KVM Connection128
- Connection Requirements and Authentication128
- Launch KVM over IP128
- Remote Host Login and Connection130
  - Set Network Configuration131
- Remote KVM Console132
- System Maintenance136
  - Firmware Management Options136
  - Firmware Upgrade Status137
Security137
- Authentication137
  - Local User Data Base137
- Encryption138
  - AES for Commands of KVM Keyboard & Mouse over IP138
  - Hardware Cryptographic Engines138
Miscellaneous138
- KVM and Discovery Occupy TCP and UDP Port on Network138
- Internal Video Support Resolution138
- Menu Item Definition of Java Remote KVM139
  - Default IP Address Source Configuration139
IPMI LAN Commands139
Connectors and Jumpers141
- Mainboard142
  - Connectors142
  - Jumpers143
- Midplane144
- Interposer Board145
- Fan Board146
- Pcie Riser146
Troubleshooting147
- BIOS Checkpoints148
  - Intel Memory Reference Code Checkpoints148
- Hardware Failure149
- Hardware Failure Troubleshooting Matrix152
- Sol154
  - Regulatory and Compliance Information157
Electromagnetic Compatibility Notices158
- FCC Verification Statement (USA)158
- Europe (CE Declaration of Conformity)159
- VCCI (Japan)159
- BSMI (Taiwan)159
- Regulated Specified Components159
- Restriction of Hazardous Substances (Rohs) Compliance160
- End of Life / Product Recycling160
Product Regulatory Compliance Markings161

Table of Contents

Related product manuals