Rohde & Schwarz SMW-K144 - Page 186

Remote-Control Commands
R&S
®
SMW-K144
186User Manual 1178.8013.02 ─ 06
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:SCSPacing....... 186
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:RBNumber........187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:RBNumber........187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:RBOFfset......... 187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:RBOFfset......... 187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:PRBoffset?....... 187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:PRBoffset?....... 187
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:DFReq?............188
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:DFReq?............188
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:NBWParts
<UserUlBwp>
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:NBWParts
<UserDlBwp>
Sets the number of downlink bandwidth parts (BWP).
Parameters:
<UserDlBwp> integer
Range: 1 to 4
*RST: 1
Example: See Example "Configuring the users and the BWPs"
on page 151.
Manual operation: See "Number of DL/UL BWPs" on page 54
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:
INDicator <BWPIndicator>
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
INDicator <BwpIndicator>
Sets the indicator for the selected BWP.
Parameters:
<BwpIndicator> integer
Range: 0 to 3
*RST: 0
Example: See Example "Configuring the users and the BWPs"
on page 151.
Manual operation: See "BWP Indicator" on page 54
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:UL:BWP<dir0>:
SCSPacing <SCSPacing>
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
SCSPacing <SCSpacing>
Selects a combination of the subcarrier spacing (SCS) and the cyclic prefix (CP).
DL/UL BWP Commands