Rohde & Schwarz SMW-K144 - Page 196

Remote-Control Commands
R&S
®
SMW-K144
196User Manual 1178.8013.02 ─ 06
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:ZP:
SET<gr0>:RES<user0>:BITMap............................................................................199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:BITMap............................................................................199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:ZP:
SET<gr0>:RES<user0>:I0.................................................................................... 199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:ZP:
SET<gr0>:RES<user0>:I1.................................................................................... 199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:I0.................................................................................... 199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:I1.................................................................................... 199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:SCID............................................................................... 199
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:PWR............................................................................... 200
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:APMap:MAPCoord............................................................200
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:APMap:AP<s2us0>:ROW<s3us0>:REAL............................ 200
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:APMap:AP<s2us0>:ROW<s3us0>:IMAGinary..................... 200
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:APMap:AP<s2us0>:ROW<s3us0>:MAGNitude....................201
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:NZP:
SET<gr0>:RES<user0>:APMap:AP<s2us0>:ROW<s3us0>:PHASe..........................201
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:
ZP:STATe <State>
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:
NZP:STATe <State>
Enables the NZP/ZP CSI-RS transmission.
Parameters:
<State> 0 | 1 | OFF | ON
*RST: 0
Example: See Example "Configuring the CSI-RS settings" on page 155.
Manual operation: See "State" on page 66
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:
ZP:SET<gr0>:NRESources <Resources>
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:CSIRs:
NZP:SET<gr0>:NRESources <Resources>
Sets the number of CSI-RS resources.
BWP Configuration Commands