Rosemount 5402 - Page 44

To Next Page

To Previous Page

Reference Manual

00809-0100-4026, Rev FA

July 2009

Rosemount 5400 Series

3-20

Figure 3-20. Recommended

hole size for pipe installations.

min. 6 in. (150 mm)

max. Ø: D/10.

Main Page

Table of Contents5
Safety Messages11
Section 1 Introduction11
Manual Overview13
Service Support14
Product Recycling/Disposal14
Theory of Operation15
Application Examples16
- Tanks, Vessels, and Containers with Calm Surfaces16
- Overfill and Underfill Detection16
- Corrosives16
- Sticky, Viscous and Crystallizing Products16
- Sludges and Slurries16
- Reactor Vessels17
- Mounting Flexibility17
- Underground Tanks17
Components of the Transmitter18
System Architecture19
Process Characteristics20
- Dielectric Constant20
- Foam20
- Turbulence20
- Temperature/Pressure20
- Density and Vapor20
- Condensation20
- Tank Characteristics20
Antenna Selection Guide/Measuring Range21
Safety Messages25
Installation Procedure26
Mounting Considerations27
- Mounting Location27
- Nozzle Considerations29
- Service Space33
- Beamwidth34
- Vessel Characteristics36
- Disturbing Objects36
- Valves36
Mounting37
- Cone Antenna Flange Connection37
- Process Seal Antenna38
- Rod Antenna Threaded Connection39
- Rod Antenna Flanged Connection40
- Bracket Mounting on Wall41
- Bracket Mounting on Pipe42
- Mounting in Pipes43
  - Recommendations for Pipe Installations43
Safety Messages45
Cable/Conduit Entries47
- Conduit Electrical Connector Wiring (Using Minifast®)48
Grounding49
Cable Selection49
Hazardous Areas49
External Circuit Breaker49
Power Requirements49
Connecting the Transmitter50
Non-Intrinsically Safe Power Supply51
Intrinsically Safe Power Supply52
- IS Parameters53
Optional Devices53
- Tri-Loop HART to Analog Converter53
- 751 Field Signal Indicator54
Safety Messages55
Overview56
- Basic Configuration Parameters57
- Tank Geometry57
  - Tank Height57
- Measurement Units57
- Process Conditions59
- Volume Configuration60
- Analog Output63
- Echo Tuning64
- Amplitude Threshold Curve65
Basic Configuration Using Rosemount Radar Master65
- System Requirements65
  - Hardware65
  - Software66
- Help in RRM66
- Installing the RRM Software for HART Communication67
  - Getting Started67
- Specifying the COM Port68
- To Set the COM Port Buffers68
- Specifying Measurement Units68
- Guided Setup69
- Using the Setup Functions74
Configuration Usinga 375 Field Communicator75
Basic Configuration Using AMS Suite78
HART Multidrop Configuration79
Safety Messages81
Viewing Measurement Data82
- Using the Display Panel82
- Specifying Display Panel Variables83
- Viewing Measurement Data in RRM86
- Viewing Measurement Data in AMS Suite87
LCD Error Messages88
LED Error Messages89
- Example89
Safety Messages91
Troubleshooting Overview93
Service Overview94
Analyzing the Measurement Signal94
Surface Pulse Not Found95
- Registration of False Echoes97
Using the Echo Curve Analyzer99
- The Configuration Mode Tab100
- The View/Record Mode Tab101
- File Mode Tab101
- Using the Echo Curve Analyzer with a 375 Field Communicator102
Analog Output Calibration104
Logging Measurement Data104
Backing up the Transmitter Configuration105
Diagnostics107
- Rosemount Radar Master107
- Ams107
- HART Command107
Configuration Report108
Viewing Input and Holding Registers108
Reset to Factory Settings109
Surface Search110
Using the Simulation Mode110
Write Protecting Atransmitter110
Diagnostic Messages111
- Troubleshooting111
- Device Status111
- Errors112
- Warnings113
- Measurement Status114
- Volume Calculation Status115
- Analog Output Status116
- Application Errors117
APPENDIX A Reference Data121
APPENDIX A Specifications121
Temperature and Pressure Ratings124
- Flange Temperature124
- Operating Pressure124
- Electronics Temperature124
Dimensional Drawings and Mechanical Properties125
Process Connections129
Ordering Information132
Spare Parts138
APPENDIX B Safety Messages145
Safety Messages145
EU Conformity146
European ATEX Directive Information147
- Intrinsic Safety147
  - Special Conditions for Safe Use (X147
- Flameproof148
  - Special Conditions for Safe Use (X148
Hazardous Locations Certifications149
- Factory Mutual (FM) Approvals149
- Canadian Standards Association (CSA) Approval150
- Dual Seal150
- Iecex Approval151
- Technology Institution of Industrial Safety (TIIS) Approval153
- National Supervision and Inspection Center for Explosion Protection and Safety of Instrumentation (NEPSI) Approvals154
Approval Drawings155
Tank Geometry161
- Distance Offset (G161
- Minimum Level Offset (C162
- Hold off Distance162
- Calibration Distance162
- Appendix C163
Advanced Analog Output Settings163
Advanced Transmitter Settings164
- Antenna Type164
- Empty Tank Handling164
- Full Tank Handling165
- Double Bounce165
- Surface Echo Tracking165
- Filter Settings166
  - Damping Value166
  - Activate Jump Filter166
Advanced Functions in RRM167
- Empty Tank Handling167
- Full Tank Handling170
- Double Bounce171
- Surface Echo Tracking172
- Hold off Setting173

Rosemount 5402 - Page 44

Table of Contents

Related product manuals