Shimadzu TXB2201L - Page 59

BEFORE
WEIGHING
MAINTENANCE
TROUBLESHOOTING
FOR YOUR
INFORMATION
USING THE
BALANCE
USING MORE CONVENIENTLY
59
2
Enter the calibration weight value.
If necessary change the weight value displayed
to match the weight that will be used for
calibration. If there is no need to change it,
proceed to step
3
.
(Enter a weight value if necessary.)
^
"Entering Numerical Values", page 49
For details on the range of weight values that
can be used, see "Specications" (^ page
145).
With models that don't feature the windbreak
3
Place the calibration weight on the
pan.
Wait until the ashing weight value display
changes to a ashing zero.
4
Take the calibration weight off the
pan.
"END" will be displayed and the balance will
return to the weighing mode.
*
If "ERR C" is displayed…
Calibration has failed for one of the
reasons given below.
There is too large a discrepancy
between the zero point of the
balance and the sensitivity.
A container has been placed on the
pan.
The pan is not on the balance.
The wrong weight has been placed
on the pan.
No operation has been performed
within 60 seconds of the ashing
weight value or zero display.
Press ( with the TXB series)
and repeat the operation from the
beginning.





!3!0!0.0!0!0
!2!9!9.9!9!8
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
!3!0!0.0!0!0
!2!9!9.9!9!8
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
! ! !0.0!0!0
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
! ! !0.0!0!0
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
!E!N!D !E!N!D
With models that feature the windbreak
3
Place the weight on the pan.
Open the glass door in the windbreak, place the
weight on the pan, and shut the glass door again.
Wait until the ashing weight value display
changes to a ashing zero.
*
Shut the glass door fully.
After placing a weight on the pan or
removing a weight from the pan, check
that the glass door is fully shut.
4
Take the calibration weight off the
pan.
Open the glass door in the windbreak, remove
the weight from the pan and shut the glass door
again.
"END" will be displayed and the balance will
return to the weighing mode.
*
With the TWC**3L, TXC**3L…
Avoid doing the following:
Putting your hand inside the glass door of the windbreak
Touching the container or sample with bare hands
Weighing samples (items to be weighed) of different temperatures
The heat will lead to convection, and this may make the balance display unstable.
You are recommended to use forceps or gloves to carry containers and samples.
When dealing with samples (items to be weighed) at different temperatures, eliminate the temperature
difference by leaving the samples around the pan inside the glass door before weighing.



! ! !0.0!0!0
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
! ! !0.0!0!0
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
!E!N!D !E!N!D