SICK CLV 45 Series - Page 170

Kapitel 10 Operating Instructions
CLV 45x Bar Code Scanner
10-66
©
SICK AG · Division Auto Ident · Germany · All rights reserved 8 009 139/K949/06-06-2002
Appendix
10.16 Index
A
Abbreviations ..................................................................................E-9
Accessories .............................................................................. 10-51
Adjusting........................................................................................... 4-8
Adjusting mode
- Activation................................................................................ 6-23
- Function.................................................................................. 4-10
AMV/S 40 connection module
- Block diagram ......................................................................... 5-1
- Cables ........................................................................................ 5-1
- Correction terminal assignment.................................... 4-11
- Function..................................................................................... 5-1
- Installation ............................................................................. 4-11
Angle of inclination (pitch)
- Definition ................................................................................... 4-5
- Limit............................................................................................. 4-5
Angle of rotation (skew)
- Definition ................................................................................... 4-5
- Limit............................................................................................. 4-5
Aperture angle
- Definition ................................................................................... 4-4
- Max. value ................................................................................ 4-5
Auto Setup
- Activating with CLV-Setup................................................ 6-15
- Activating With Profile bar code.................................. 10-28
- Function.................................................................................. 6-14
- Procedure .............................................................................. 6-14
Auxiliary input
- Activation............................................................................. 10-46
- Function.................................................................................. 6-28
Azimuth angle (tilt)
- Definition ................................................................................... 4-5
- Limit............................................................................................. 4-5
B
Bar code samples (scannable)......................................... 10-69
Beeper (buzzer)
- Function..................................................................................... 3-9
- Parameterization.................................................................... 3-9
- Position .............................................................................3-3, 3-4
C
Cables
- Overview.............................................................................. 10-52
- Wire color assignment ......................................................... 5-4
CLV Assistant ........................................................................... 10-27
CLV-Setup
- Default setting................................................................... 10-22
- Download.................................................................................. 6-5
- Functions............................................................................. 10-25
- Handling unknown parameters .................................. 10-26
- Installation at PC .............................................................. 10-20
- Recording log file of serial communication ............ 10-27
- Starting................................................................................. 10-22
- Tab cards.................................................................................. 6-6
- Upload........................................................................................ 6-5
- User interface.................................................................... 10-24
Code angle CW
- Counting direction..................................................................4-6
- Output.........................................................................................4-7
- Parameterization.....................................................................6-8
Code length
- Entering unknown lengths.............................................10-39
Code position CP
- Counting direction in the scan line ..................................4-6
- Output.........................................................................................4-7
- Parameterization.....................................................................6-8
Command strings
- Function ...................................................................10-1, 10-33
- Input in the terminal emulator.....................................10-34
Configuration...................................................................................6-4
Connection schema.....................................................................5-1
D
Declaration of conformity.....................................................10-64
Decoder
- SMART decoder......................................................................3-5
- Standard decoder..................................................................3-5
Default setting
- CLV extract ...............................................................................6-2
- CLV-Setup ...........................................................................10-22
- printing out CLV.......................................................................6-1
Design
- Line scanner.............................................................................3-3
- Line scanner with oscillating mirror .................................3-4
Device functions
- Carrying out in dialog box.................................................6-29
Device number GN.......................................................................5-3
Device variants ..............................................................................3-1
DeviceNet ..................................................................................10-48
Dimensional drawings .................................................................9-3
Dismantling
- Disposal .....................................................................................7-2
- Procedure...............................................................................4-14
Disposal............................................................................................7-2
Distance configuration
- Function .....................................................................................3-6
- Parameterization.....................................................................6-8
Documentation (supplementary)......................................10-56
Download
- Executing...................................................................................6-5
- Function .....................................................................................6-5
E
Electrical installation.....................................................................5-1
EMC....................................................................................................9-2
Enclosure rating.............................................................................9-2
Error messages
- Display in the terminal emulator.......................................8-2
- Function .....................................................................................3-5
- Listing.......................................................................................6-30
Error status in the read result ..................................................8-5
Ethernet ......................................................................................10-49
Evaluation
- Decoder types.........................................................................3-5
- Parameterization..................................................................6-12