SICK FLOWSIC500 User Manual

162 FLOWSIC500 · Operating Instructions · 8025733/1GMJ/V4-2/2022-07 · © SICK Engineering GmbH
Annex
Subject to change without notice
Fig. 82 Control diagram 9215965 (page 3)
SICK Engineering GmbH
Bergener Ring 27 01458 Ottendorf-Okrilla
Verteildatum: Page
Ersatz für:
Änderung
gez.
Tag
Name
Ind.
Tag Name
Maßstab:
Werkstoff Ersetzt durch:
Gepr.
Ursprung:
MKO
3of7
2014-07-16
Connector. Function / signal Internal conne ct ion Operating
parameters
Safety parameters*)
M12 , male, B-coded Pin 1 ext. power supply “–” (GND) “BAT1 –“ terminal nominal
input voltage 4.5…16 V
Ui = 20 V Ii = 667 mA Pi = 772 mW
Pin 2 ext. power supply “+” “BAT1 +” terminal Pin 3 Digital output DO1 “–“ (GND) “DO1 –“ terminal
passive, non-isolated, Low side switch
max.16 V nom. 20 mA Ron < 110 Ohm Roff >1 MOhm
Ui = 20 V Pi = 1.1 W Uo = 8.2 V Io = 0.83 mA Po = 1.7 mW Co = 7.6 μF Lo = 100 mH
Pin 4 Digital output DO1 “+“ “DO1 +” terminal M12, male, A-coded
Configuration “2 Digital outputs LF”
passive, optically isolated
Pin 1 Digital output DO2 “+“ “ DO2 +” terminal max.16 V
nom. 20 mA switchable as NAMUR nominal 8.2 V Ion = 3.4 mA Ioff = 0.7 m A
Ui = 20 V Pi = 1.1 W
Pin 2 Digital output DO2 “-“ “DO2 –“ terminal Pin 3 Digital output DO3 “–“ “DO3 –“ terminal Pin 4 Digital output DO3 “+“ “ DO3 +” terminal
Preselected Configuration for circular connectors M12, male Configuration “2 Digital outputs LF”
*) values apply for the interconnection of all circuits within each connector
Optionally Exia Temperature Sensor
Optionally Exia pressure sensor
Ultrasonic Transducers
Temperature range and pressure range see Marking plate
Class I, Division 1, Groups C and D, Temp. Code T4 Ex ia IIB T4 Ga ClassI,Zone0AExiaIIBT4Ga
.
-25°C < Tamb < 60°C
,
for extended range see Marking plate
.
In the US install in accordance with the NEC (NFPA70, Article 504) and ANSI/ISA-RP12.06.01 In Canada install in accordance with CEC part 1
Exia Intrinsically Safe; Securite Intrinseque
9215965
M12
ext. Power + DO1
DO2 + DO3
M12
Wire size for all terminals: 0,14..0, 5 mm (AWG 24 ... 20)
2
4mm (AWG 12)
2
EXT. POWER
BAT1
n.c.
DO3
DO0
+-
P1
P2
T1
T2
SENSORS
DISPLAY
LOCK
OFF ON
5..12V
NAMUR
4,5..16V
1.5 mm² (AWG 16)
:
R:100
S
2..16V
2..16V
DO2
2..16V
DO1
+-
BAT2
+-
+- +- +-
kochami
draft
01
2014-08-27
gepr.
kochami
2014-08-27
Control drawing FLOWSIC500 isolated I/O
kochami
Ed.6
02
WARNING: EXPLOSION HAZARD Substitution of components may impair Intrinsic safety AVERTISSEMENT: La substituti on de composants peut compromettre la securite intrinseque.
RISQUE D` EXPLOSION -
2015-09-24
kochami
ZY57
03
2018-05-02

SICK FLOWSIC500 Specifications

General

Brand	SICK
Model	FLOWSIC500
Category	Measuring Instruments
Language	English