What to do if Terumo Medical Equipment doesn't switch to battery after AC power loss?
If your Terumo Medical Equipment doesn't switch to battery power when the AC power is cut off, the battery may be low. Charge the battery. If charging doesn't solve the problem, the battery may be damaged.
What if the AC power lamp doesn't light up on Terumo Medical Equipment?
If the AC power lamp on your Terumo Medical Equipment doesn't light up, ensure the AC power source is properly connected by reconnecting the AC power cable.
How to fix unstable flow display on Terumo Medical Equipment?
If the flow is displayed as “-.--” and is unstable, it may be due to several reasons: * The ABD/Flow Sensor is not properly connected: Reconnect the ABD/Flow Sensor. * The ABD/Flow Sensor is not properly attached on the tube: Reattach the ABD/Flow Sensor on the tube. * The detection window of the ABD/Flow Sensor is dirty: Remove the ABD/Flow Sensor from the tube to clean, reapply vaseline and reattach on the tube.
Why can't I export history data to USB from Terumo Medical Equipment?
If the button that exports history data to a USB memory drive does not function, it may be because the Drive Motor is running. Output data to the USB memory drive after stopping the Drive Motor.
Why is the temperature display unstable on Terumo Medical Equipment?
If the temperature is displayed as “--.-” and is not stable, it could be because: * The Temperature Sensor Cable is not properly connected: Reconnect the Temperature Sensor Cable. * The CAPIOX Luer Thermistor is not properly connected: Reconnect the CAPIOX Luer Thermistor. * The CAPIOX Luer Thermistor has failed: Replace the CAPIOX Luer Thermistor.
Why motor speed displayed as '----' on Terumo Medical Equipment?
If the motor speed is displayed as “----” and the centrifugal pump does not rotate, the Drive Motor might not be properly connected. Reconnect the Drive Motor.
Why doesn't the charge lamp light up on my Terumo Medical Equipment?
If the charge lamp does not light up, it might be because the battery is fully charged, meaning it cannot be charged further, and there is no abnormality.
What if Terumo Medical Equipment battery doesn't reach 100% after charging?
If the battery charge level is less than 100% even after charging is completed, the battery may have deteriorated.
Why doesn't the clamp ready lamp light up on Terumo Medical Equipment?
If the Clamp ready lamp does not light up, check the following: * The Fast Clamp is not properly connected: Connect the Fast Clamp. * The fast clamp function is not on: Enable the fast clamp function. * The safety connection which allows the Fast Clamp to operate has not been set: Set the safety connection. * The tube has not been securely set or the lid is not properly closed: Set the tube and close the lid.
Why can't I clamp from the Fast clamp screen on Terumo Medical Equipment?
If the Fast Clamp cannot be clamped from the button on the Fast clamp screen, it could be because: * The tube has not been securely set or the lid is not properly closed: Set the tube and close the lid. * The fast clamp function is not on: Enable the fast clamp function. * The Drive Motor is running: Execute the clamp after stopping the Drive Motor.
Details the physical layout and components of the CAPIOX EBS.
Provides critical safety guidelines for operating the CAPIOX EBS system.
Outlines proper storage conditions to maintain device integrity.
Step-by-step guide for setting up the CAPIOX EBS system.
Detailed steps for priming the CAPIOX EBS circuit before use.
Instructions for connecting the CAPIOX EBS to the patient circuit.
Procedure for initiating the bypass function of the CAPIOX EBS.
Guidelines for operating the CAPIOX EBS during perfusion.
Steps for safely terminating the bypass procedure.
Procedure for replacing the CAPIOX EBS circuit.
Technical data and specifications for the CAPIOX EBS.
Introduction to the CAPIOX Centrifugal Pump Controller SP-200.
Highlights key features of the CAPIOX Centrifugal Pump Controller SP-200.
Illustrates the system setup with the controller and connected components.
Describes the front, control panel, rear, and bottom views of the controller.
Explains coast speed behavior and LCD touch panel displays.
Details controller display units, optional accessories, and related components.
Covers broad safety guidelines for system operation and handling.
Details safety advice for specific components like the controller and sensors.
Addresses electrical safety, environmental factors, and electromagnetic interference.
Provides guidelines for proper storage and cleaning procedures.
Specific precautions for installing and using the system in an ambulance.
Guide for initial system setup and touch panel interaction.
Steps for preparing the system and attaching the controller to the cart.
Instructions for connecting AC power, drive motor, sensors, and cables.
Details inspections required before circulation and how to start it.
Procedures for connecting the centrifugal pump and attaching components.
Steps for connecting temperature/pressure sensors and filling with priming solution.
Covers powering on the system, confirming setup, auto-priming, and calibration.
Instructions for attaching, using the attachment, and using the arm of the Fast Clamp.
Guidelines for operation during circulation and the weaning process.
Procedure for safely shutting down the system.
Details on assembling the cart, locking casters, and moving the unit.
Instructions for attaching accessories like gas blenders and oxygen cylinders.
Explains the two setup modes: User and Admin.
Configuration of flow and pressure alarm thresholds.
Setup for pressure and temperature measuring functions and alerts.
Configuration of fast clamp and air bubble detector functions.
Setting safety responses and reviewing alarm configurations.
Setup for Body Surface Area calculation, timers, and history tracking.
Procedures for exporting data via USB and managing logs.
Accessing and managing admin setup and passwords.
Details settings for presets, auto-priming, coast speed, and communication.
Technical specifications for the CAPIOX Centrifugal Pump Controller SP-200.
Details alarms, available functions, and environmental/power conditions.
Physical dimensions, weight, and list of related components.
Guidance on electromagnetic compatibility and emissions.
Guidance on electromagnetic immunity for the system.
General| Product Name | Terumo CAPIOX EBS Circuit with X coating |
|---|---|
| Category | Medical Equipment |
| Manufacturer | Terumo |
| Coating Type | X coating |
| Usage | Extracorporeal circulation during cardiopulmonary bypass |
| Type | Extracorporeal Blood Circuit |
| Compatibility | Compatible with Terumo CAPIOX oxygenators |
To Next Page
