Toshiba e-STUDIO6520c - Page 194

e-STUDIO5520C/6520C/6530C © 2008-2011 TOSHIBA TEC CORPORATION All rights reserved
SELF-DIAGNOSTIC MODE
2 - 156
2nd transfer roller 1240-0 to 8 1241 <Default values of code 1240
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 225,000/250,000/
275,000
Sub-code 4: 242,000/242,000/
242,000
2nd transfer roller blade
cleaner
1242-0 to 8 1243 <Default values of code 1242
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 225,000/250,000/
275,000
Sub-code 4: 242,000/242,000/
242,000
Pressure roller 1250-0 to 8 1251 <Default values of code 1250
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 450,000/500,000/
550,000
Sub-code 4: 1,804,000/1,804,000/
1,804,000
Pressure roller separation
finger
1270-0 to 8 1271 <Default values of code 1270
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 450,000/500,000/
550,000
Sub-code 4: 1,804,000/1,804,000/
1,804,000
Fuser belt 1272-0 to 8 1273 <Default values of code 1272
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 225,000/250,000/
275,000
Sub-code 4: 902,000/902,000/
902,000
Fuser roller 1274-0 to 8 1275 <Default values of code 1274
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 225,000/250,000/
275,000
Sub-code 4: 902,000/902,000/
902,000
Fuser belt guide 1276-0 to 8 1277 <Default values of code 1276
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 225,000/250,000/
275,000
Sub-code 4: 902,000/902,000/
902,000
Pickup roller
(RADF)
1282-0, 1, 2, 8 1283 <Default values of code 1282
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 120,000/120,000/
120,000
Feed roller
(RADF)
1284-0,1,2,8 1285 <Default values of code 1284
(e-STUDIO5520C/6520C/6530C)>
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 120,000/120,000/
120,000
Items
PM management
setting <Procedure
4> *Indicated in 8
digits
Date of previous
replacement
<Procedure 2>
Remarks