Need help?Do you have a question about the Vatech Smart Plus PHT-35LHS and is the answer not in the manual?
Provides essential preliminary information and safety guidelines before operating or servicing the equipment.
Explains the use of symbols and warnings for safety information in the manual.
Details operator qualifications and general safety precautions for using the equipment.
Provides critical instructions for electrical and mechanical safety to prevent damage or injury.
Highlights radiation safety precautions and necessary measures for operating the X-ray system.
Lists essential checkpoints for service technicians to confirm before performing procedures.
Lists commands for optimizing image quality in CT and PANO modes.
Illustrates the system and power block diagrams of the Smart Plus device.
Details the configuration of main MCU, power, and noise filter boards in the vertical frame.
Provides step-by-step instructions for disassembling the covers of the vertical, rotating, handle, and CEPH units.
Details procedures for optimizing CBCT image quality through preliminary and dark/bright calibration.
Guides on setting up bead phantom offset, acquiring and reconstructing images for geometry calibration.
Explains procedures for aligning CBCT collimators for left/right and top/bottom positions.
Covers first position setup procedures using CT phantoms for optimizing CBCT image quality.
Details sensor calibration procedures for PANO mode, including dark and bright calibration.
Explains the first collimator alignment operation for PANO mode in adult and child modes.
Guides on performing PANO geometry calibration, including pin distance, center pin, and ball size.
Details standards for PANO image inspection, including line pair, contrast, noise, and homogeneity.
Covers configuring CEPH sensor and performing dark and bright calibration for quality CEPH images.
Guides on performing CEPH geometry calibration using console software and phantoms.
Details CEPH collimator alignment using EzAlign and performing the 4% cut evaluation.
Provides instructions on downloading and installing the Flash Loader Demo software for firmware upgrades.
Guides on performing firmware upgrade using STMFlashLoader Demo and Terminal v1.9b.
Explains how to check the firmware version of the MCU boards using the Terminal v1.9b program.
Details the communication setting parameters for serial communication via HyperTerminal.
Lists PANO, CEPH, CT, and common commands for controlling the Smart Plus device.
Provides a list of tube and motor error messages sent from MCU to PC with their descriptions.
Provides essential preliminary information and safety guidelines before operating or servicing the equipment.
Explains the use of symbols and warnings for safety information in the manual.
Details operator qualifications and general safety precautions for using the equipment.
Provides critical instructions for electrical and mechanical safety to prevent damage or injury.
Highlights radiation safety precautions and necessary measures for operating the X-ray system.
Lists essential checkpoints for service technicians to confirm before performing procedures.
Lists commands for optimizing image quality in CT and PANO modes.
Illustrates the system and power block diagrams of the Smart Plus device.
Details the configuration of main MCU, power, and noise filter boards in the vertical frame.
Provides step-by-step instructions for disassembling the covers of the vertical, rotating, handle, and CEPH units.
Details procedures for optimizing CBCT image quality through preliminary and dark/bright calibration.
Guides on setting up bead phantom offset, acquiring and reconstructing images for geometry calibration.
Explains procedures for aligning CBCT collimators for left/right and top/bottom positions.
Covers first position setup procedures using CT phantoms for optimizing CBCT image quality.
Details sensor calibration procedures for PANO mode, including dark and bright calibration.
Explains the first collimator alignment operation for PANO mode in adult and child modes.
Guides on performing PANO geometry calibration, including pin distance, center pin, and ball size.
Details standards for PANO image inspection, including line pair, contrast, noise, and homogeneity.
Covers configuring CEPH sensor and performing dark and bright calibration for quality CEPH images.
Guides on performing CEPH geometry calibration using console software and phantoms.
Details CEPH collimator alignment using EzAlign and performing the 4% cut evaluation.
Provides instructions on downloading and installing the Flash Loader Demo software for firmware upgrades.
Guides on performing firmware upgrade using STMFlashLoader Demo and Terminal v1.9b.
Explains how to check the firmware version of the MCU boards using the Terminal v1.9b program.
Details the communication setting parameters for serial communication via HyperTerminal.
Lists PANO, CEPH, CT, and common commands for controlling the Smart Plus device.
Provides a list of tube and motor error messages sent from MCU to PC with their descriptions.
General| Brand | Vatech |
|---|---|
| Model | Smart Plus PHT-35LHS |
| Category | Medical Equipment |
| Language | English |
To Next Page
