Wallace Perimeter Security ALPHA - Page 169

182 pages

Save Page as PDF

To Next Page

To Previous Page

Figure 48. Schemac for Kinec DCS 15 [Kinec 1S] and Kinec DCS 10F [Kinec 2S] Solar Operator(s)

Main Page

Table of Contents3
Kinetic Components7
Product & Warranty Registration8
Introducing Kinetic DC9
Intelligent Features: Smartdc Controller9
Technical Support10
Alpha/Delta (Kinetic Operator) Gate System10
Alpha/Delta Installation & Maintenance Checklist12
Safety Information19
Safety Notices19
Common Industrial Symbols19
Safety Requirements20
Important Safety Instructions20
Safety Standards - Installer's Responsibility21
Safety Standards - Owner/User Responsibility23
Hazardous Materials and Proper Disposal24
External Entrapment Protection Sensors25
Identifying Gate Operator Category and Usage Class27
Choosing External Entrapment Protection28
UL 325 Compliant Sensors29
Stop Button31
Manual Release31
Alpha/Delta Gate Unloading32
ALPHA/DELTA Gate Installation33
ALPHA Gate Model Step-By-Step Installation Diagrams35
DELTA Gate Model Step-By-Step Installation Diagrams46
Operator Installation and Gate Adjustments57
Installing the Kinetic Operator on Gate Posts58
Adjusting the Drive Height59
Adjusting the Spur Gear Alignment59
Installing the Tooth Rack60
Connecting the Battery and Turning DC Power61
Programming the Initial Setup Menu61
Establishing the OPEN and CLOSE Limits63
Target Sensor Rack Drive Installation Instructions64
Installing the Target Magnet66
Power68
Installing the Earth Ground68
Wiring AC Power70
Wiring 115VAC Power71
Wiring 230VAC Power72
Using a Solar Powered Operator74
Design Requirements and Considerations74
Connecting Peripherals to a Solar Operator76
Understanding Gate Activity Based on Solar Zones77
Important Considerations for DC-Power Connection79
Installing the Extended Battery Backup Kit80
Display and Menu Options82
Initial Setup82
Turning both Power Switches on83
Using the Smartdc Controller Buttons in Menu Mode85
Run Mode86
Understanding Gate Status Displays86
Using the Smartdc Controller Buttons in RUN Mode87
Viewing Operator Status Displays88
User Menu89
Adjusting the Close Timer90
Setting the Time and Date91
Setting AC Power Loss Gate Function92
Adjusting the Display Contrast93
User Menu Functions94
Installer Menu98
Resetting the OPEN and CLOSE Limits99
Adjusting the Gate Speed100
Adjusting the IES Sensitivity101
Reinstating Factory Defaults104
Enabling the Fire Department Override105
Installer Menu Functions106
Smartdc Controller115
Overview of the Smartdc Controller116
Preliminary Testing117
Vehicle Detector Installation Options120
Connecting HY5B Vehicle Detectors121
Connecting Standard 11-Pin Box Type Vehicle Detectors124
Vehicle Detector Configuration and Quick Close Mode Selection126
Entrapment Sensor Connections127
Manual Push-Button Station128
User Relays - Programming Procedure129
Bi-Parting Gate Systems134
Power Requirements134
Primary and Secondary Wiring Connections135
Primary and Secondary Menu Setup136
Reference138
Connecting a Radio Receiver for Remote Open138
Installing a Maglock or Solenoid Lock139
Installing a Lock for 12VDC or 24VDC Systems139
Installing a Lock for a High Voltage System140
Setting the User Relay Function in the Installer Menu141
Installing Vehicle Detectors and Loops142
Installing Photoelectric Sensors for External Entrapment Protection Only145
Operation Notes145
Photo Eye Mounting and Alignment147
Installing Gate Edge Sensors148
Accessory Connections149
Smartdc Controller Troubleshooting151
Troubleshooting152
Vehicle Detector and Loop Fault Diagnostics163
Kinetic Schematics166
General Maintenance171
Smart Touch Analyze and Retrieve Tool (S.T.A.R.T.)171
Electrical Controls173
Mechanical Maintenance173
Software Maintenance174
Drive Belt Tension and Alignment174
DC Battery Replacement176
Clock Battery Replacement178
Kinetic DC Specifications181

Wallace Perimeter Security ALPHA - Page 169

Table of Contents