WinGD X92 - Page 5

2/3
31/12/2021
Modification Service
Engine Documentation
W-X92
Summary for Maintenance Manual
Page No.
Modification
Title
Subject
Page or
Date
No.
Manual
new
exch.
3303-5/A2
2017
WinGD Input
Top End Bearing
Cover
Different procedure with new tool
x
3326-1/A1
2016-10
EAAD086618
Crosshead Pin -
Removal / Installation
/ Clearance Checks
Pge 6 and 11, Note added ref Fig, 13 and Fig. 25.
x
3326-1/A1
2016-10
EAAD086515
Crosshead Pin -
Removal / Installation
/ Clearance Checks
Procedure to remove and install the Crosshead Bearing -
Temperature Monitor added to document. Full document
update.
x
3425-1/A1
2016-02
WinGD Input
Wear of Piston Rings
and Ring Grooves
Correction of ring type designation
x
5552-1/A2
2016
WinGD Input
Camshaft and Bearing
Shells - Removal and
Installation
New document for supply unit with independent lubrication
system
x
5562-1/A2
2016
New drawing
PCV On-board Repair
Kit
New document
x
9403-5/A1
2016-10
EAAD086688
EAAD086892
Standard Tools
Page 7, Illustration update of double pre-tensioner.
Pge 9, Brackets updated. Dimension of brackets changed.
x
Date of publication 2017-01-18
9403-5/A1
2017-11
e-mail and
EAAD088154
Standard Tools
Pge 2: Data change to 94010, 94012 and 94015-008. Pge 3:
Manual ratchet and chain block numbers changed. Pge 6:
94110A removed. 94110 amended. Pge 7: Data change to
94117B and 94117. Pge 8: Dimension changes to 94118A to
D. Pge 9: Dimension change to 94141A. Pge 10: Platform
94143A added. 94143 amended. Pge 12: New optional lifting
tool for the water guide jacket added. Pge 15: 94265 WLL
amended. Cutting device replaced with new Grinding Device.
Pge 16: Valve holder 94272A removed. Pge 18: 94319
amended. Pge 21: Tool 94336A added. Pge 22: 94337
amended. Pge 24: 94110/A quntities amended. Pge 25: 94556
removed. Pge 29: 94592D amended. Pge 31: Covers added.
Pge 32: Left and right supports added. Support 94663M
added. Dimensions changed. Pge 33: 94870G changed to
AF55. Pge 34: 94934A pressure amended. Pge 36: Pressure
gauge replaced with 93434H. Pge 35: Distributing piece
94934C added. 94934I Connection nipple replaced. 94934J,
Tredo joint added. 94934K/L Adapter piece added. Pge 39:
Calliper gauge added. Pge:
x
2124-2/A1
2017-11
e-mail from
Doosan
Cylinder Liner -
Removal and
Installation
Pge1, 3, 5. Tool numbers for shackle, manual ratchet and
chain changed.
x
0380-1/A1
2017-11
EAAD080381
EAAD088727
Inspection and
overhaul intervals
Pge 3: Relief valve data added. Connecting rod bearings data
changed. Connecting rod bearings data changed. Pge 5:
Piston data changed. Piston ring data changed. Pge 7: Data
change to Lubricating pump. Page 10: EAAD088727alve
stroke sensors replacement interval changed to 66 000 Op
Hrs. All pages: Language updated.
x
2708-3/A1
2017-11
EAAD087592
Machining of Sealing
Face in Cylinder Liner
New procedure with new tool (94270G)
x
3130-1/A1
2017-11
EAAD087655
Steel Spring Vibration
Damper - Inspection
Whole document: Fig. 1 and Fig.2 updated. Language
updated.
x