Xerox ColorQube 9303 Series - Page 87

February 2013
2-63
ColorQube® 9303 Family
05-350-00, 05-352-00
Status Indicator RAPs
05-350-00, 05-352-00 DADH CVT Sensor Failure RAP
05-350-00 The DADH CVT sensor does not detect the lead edge of the document within the
correct time in the forward mode.
05-352-00 The DADH CVT sensor does not detect the lead edge of the document within the
correct time in the reverse mode.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Remove all documents from the DADH.
Procedure
NOTE: To get access to the DADH CVT sensor, remove the DADH top cover, PL 5.20 Item 15.
Enter dC330 code 05-097 to check the DADH CVT sensor Q05-097, PL 5.20 Item 12. Actuate
Q05-097.
The display changes.
YN
Refer to WD 5.1. Check Q05-097.
References:
• GP 11 How to Check a Sensor.
• P/J186 and P/J191, DADH PWB.
• 01C +3.3V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• DADH CVT sensor, PL 5.20 Item 12.
• DADH PWB, PL 5.10 Item 5.
Remove the DADH rear cover, PL 5.10 Item 1. Hold the DADH cover interlock switch closed,
PL 5.15 Item 11. Enter dC330 code 05-099 to check the DADH CVT motor, MOT05-099, PL
5.25 Item 9.
MOT05-099 runs.
YN
Go to the 05C DADH Motor Failure RAP.
The CVT roll rotates.
YN
Perform the steps that follow:
• Check the DADH CVT motor drive belt, PL 5.25 Item 11.
• Check the DADH CVT motor tension spring. Make sure that the DADH CVT motor
drive belt tension is correct, ADJ 5.1.
• Check the CVT roll pulley, PL 5.25 Item 17.
If necessary, install a new DADH CVT roll, PL 5.25 Item 5.
The fault only occurs in duplex mode (fault code 05-352-00).
YN
Go to the Final Checkout.
NOTE: The exit roll idlers remain lowered for 30 seconds.
Enter dC330 code 05-100 to check the DADH duplex solenoid, SOL05-100. Energize SOL05-
100 to lower the exit roll idlers, PL 5.35 Item 6.
The exit roll idlers lower.
YN
Refer to WD 5.1. Check SOL05-100.
References:
• GP 12 How to Check a Solenoid or Clutch.
• P/J181, DADH PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• DADH duplex solenoid, PL 5.30 Item 3.
• DADH PWB, PL 5.10 Item 5.
• Lower baffle assembly, PL 5.30 Item 14.
NOTE: During normal operation, the exit roll idlers remain raised (closed) in simplex mode. In
duplex mode, the exit roll idlers remain raised unless the document is longer than 280 mm (11
inches). The exit roll idlers raise and lower while feeding longer documents in duplex mode.
Exit the diagnostics mode. Close the DADH top cover. Make two copies in duplex mode.
Check that the second document is held in the feed rolls until the first document is fed into the
output tray.
The feed rolls held the second document.
YN
Go to the 05D DADH Feed Clutch Failure RAP.
The fault is caused if the DADH feed motor runs too slowly in reverse, refer to the 05C DADH
Motor Failure RAP. If the fault continues, go to the Final Checkout.
Final Checkout
Perform the steps that follow. Install new components as necessary:
• Check that the CVT roll is clean and rotates freely, refer to ADJ 5.4.
• Check the DADH CVT sensor, PL 5.20 Item 12 is installed correctly.
• Check the takeaway roll static eliminator and ground harness, PL 5.35 Item 7.
• Make sure that the DADH ground harness is connected correctly, PL 5.10 Item 11.
• Make sure the feed motor drive belt tension is correct, ADJ 5.1.
• DADH feed assembly, PL 5.15 Item 18.
If the fault continues, make sure that documents correctly exit the previous sensor in the docu-
ment path. Refer to the 05-335-00 DADH TAR Sensor Failure RAP.