To Next Page

To Previous Page

Services

7210 SAS M Services Guide Page 87

Deleting SDPs

The no form of the sdp command removes an SDP ID and all associated information. Before an

SDP can be deleted, the SDP must be shutdown and removed (unbound) from all customer

services where it is applied.

CLI Syntax: config>service# no sdp 79

Example

: config>service# epipe 5 spoke-sdp 79:5

config>service>epipe>sdp# shutdown

config>service>epipe>sdp# exit

config>service>epipe# exit

config>service# no sdp 79

Default Chapter3
- Table of Contents3
Preface15
- List of Technical Publications16
- Technical Support17
Getting Started19
- Alcatel-Lucent 7210 SAS Services Configuration Process19
- Table 1: Configuration Process19
- VLL Services19
- Getting Started20
- In this Chapter21
Services Overview23
- Introduction24
  - Service Types25
  - Service Policies26
- Alcatel-Lucent Service Model27
Services Overview28
- Service Entities28
Services Overview35
- Service Creation Process Overview62
- Figure 12: Service Creation and Implementation Flow62
- Deploying and Provisioning Services63
- Configuration Notes64
  - General64
- Configuring Global Service Entities with CLI65
  - Service Model Entities65
- Basic Configuration66
- Common Configuration Tasks68
  - Configuring Customers68
    - Customer Information68
  - Configuring an SDP71
    - SDP Configuration Tasks71
- Ethernet Connectivity Fault Management (ETH-CFM)74
- Service Management Tasks84
- Global Services Command Reference89
VLL Services119
- Circuit Emulation (Cpipe) Services120
  - Cpipe Service Overview120
  - Cpipe Service Modes120
- Ethernet Pipe (Epipe) Services136
- Support for Processing of Packets Received with more than 2 Tags on a Qinq SAP in Epipe Service (Only on 7210 SAS-M Network Mode)138
  - Feature Support, Configuration Notes and Restrictions139
- (Only on 7210 SAS-M Network Mode)140
Virtual Private LAN Service243
- VPLS Service Overview244
Virtual Private LAN Service245
- VPLS Features251
- BGP Auto-Discovery for LDP VPLS286
- Routed VPLS294
- Configuring a VPLS Service with CLI305
- Service Management Tasks351
- VPLS Services Command Reference357
- Table 17: Final Disposition of the Packet Based on Per FC and Per SAP Policer or Meter421
IEEE 802.1Ah Provider Backbone Bridging437
- IEEE 802.1Ah Provider Backbone Bridging (PBB) Overview438
IEEE 802.1Ah Provider Backbone Bridging439
- PBB Features439
- Configuration Examples454
  - PBB ELAN and ELINE454
  - MC-LAG Multihoming for Native PBB455
- PBB Command Reference457
  - PBB Show Commands465
Internet Enhanced Service499
Internet Enhanced Service500
- IES Service Overview500
- Figure 64: Internet Enhanced Service500
- IES Features501
  - IP Interfaces501
- Saps502
- Configuring an IES Service with CLI507
- IES Services Command Reference517
Virtual Private Routed Network Service549
Virtual Private Routed Network Service550
- VPRN Service Overview550
- VPRN Features557
Virtual Private Routed Network Service560
- CE to PE Routing Protocols563
  - PE to PE Tunneling Mechanisms563
  - Per VRF Route Limiting563
- Service Label Mode of a VPRN564
Internet Enhanced Service560
- Configuring a VPRN Service with CLI565
- VPRN Services Command Reference581
- Bgp Configuration Commands586
- Table 19: Final Disposition of the Packet Based on Per FC and Per SAP Policer or Meter624
- Pim Commands635
Show, Clear, Debug, Commands675
- Show Command Index675
Common CLI Command Descriptions939
- Common Service Commands940
Appendix: Split Horizon941
- Overview942
  - Topology942
  - Figure 69: Split Horizon Group Example942
- Configuration Guidelines943
  - Verification945
    - Standards and Protocol Support947
    - Standards Compliance947

Brand	Alcatel-Lucent
Model	7210 SAS M
Category	Switch
Language	English

Alcatel-Lucent 7210 SAS M Service Guide

Table of Contents

Other manuals for Alcatel-Lucent 7210 SAS M

Questions and Answers:

Alcatel-Lucent 7210 SAS M Specifications

Related product manuals