AudioCodes MediaPack MP-118 User Manual

Version 6.6 307 MP-11x & MP-124
User's Manual 27. SAS Configuration
Table 27-1: SAS IP to IP Inbound Manipulation Parameters
Parameter Description
Matching Characteristics (Rule)
Additional Manipulation
[IPInboundManipulation_IsAd
ditionalManipulation]
Determines whether additional SIP URI user part manipulation is
done for the table entry rule listed directly above it.
 [0] No = (Default) Regular manipulation rule (not done in
addition to the rule above it).
 [1] Yes = If the above row entry rule matched the call, consider
this row entry as a match as well and perform the manipulation
specified by this rule.
Note: Additional manipulation can only be done on a different SIP
URI, source or destination, to the rule configured in the row above
as configured by the 'Manipulated URI' parameter (see below).
Manipulation Purpose
[IPInboundManipulation_Mani
pulationPurpose]
Defines the purpose of the manipulation:
 [0] Normal = (Default) Inbound manipulations affect the routing
input and source and/or destination number.
 [1]
Routing input only = Inbound manipulations affect the routing
input only, retaining the original source and destination number.
Source IP Group ID
[IPInboundManipulation_SrcI
pGroup]
Defines the IP Group from where the incoming INVITE is received.
For any IP Group, enter the value "-1".
Source Username Prefix
[IPInboundManipulation_SrcU
sernamePrefix]
Defines the prefix of the source SIP URI user name (usually in the
From header).
For any prefix, enter the asterisk "*" symbol (default).
Note: The prefix can be a single digit or a range of digits. For
available notations, see 'Dialing Plan Notation for Routing and
Manipulation' on page 419.
Source Host
[IPInboundManipulation_SrcH
ost]
Defines the source SIP URI host name - full name (usually in the
From header). For any host name, enter the asterisk "*" symbol
(default).
Destination Username Prefix
[IPInboundManipulation_Dest
UsernamePrefix]
Defines the prefix of the destination SIP URI user name (usually in
the Request-URI).
For any prefix, enter the asterisk "*" symbol (default).
Note: The prefix can be a single digit or a range of digits. For
available notations, see 'Dialing Plan Notation for Routing and
Manipulation' on page 419.
Destination Host
[IPInboundManipulation_Dest
Host]
Defines the destination SIP URI host name - full name (usually in
the Request URI).
For any host name, enter the asterisk "*" symbol (default).
Request Type
[IPInboundManipulation_Req
uestType]
Defines the SIP request type to which the manipulation rule is
applied.
 [0] All = (Default) All SIP messages.
 [1] INVITE = All SIP messages except REGISTER and
SUBSCRIBE.
 [2] REGISTER = Only REGISTER messages.
 [3] SUBSCRIBE = Only SUBSCRIBE messages.
 [4] INVITE and REGISTER = All SIP messages except
SUBSCRIBE.

AudioCodes MediaPack MP-118 Specifications

General

Category	Gateway
Analog Ports	8 FXS ports
Voice Codecs	G.711, G.723.1, G.726, G.729A/B
Operating Temperature	0°C to 40°C (32°F to 104°F)
Storage Temperature	-20°C to 70°C (-4°F to 158°F)
Protocols	SIP, MGCP, H.323
Model	AudioCodes MediaPack MP-118
Fax Support	T.38
Management	Web-based, SNMP, CLI
Security	SRTP, TLS, HTTPS
Power Supply	AC 100-240V, 50-60Hz
Humidity	10% to 90%, non-condensing
Network Interfaces	2 x 10/100Base-T Ethernet