EasyManuals Logo

AudioCodes MediaPack MP-118 User Manual

AudioCodes MediaPack MP-118
584 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #214 background imageLoading...
Page #214 background image
User's Manual 214 Document #: LTRT-65422
MP-11x & MP-124
Parameter Description
Web: Presentation
EMS: Is Presentation
Restricted
[IsPresentationRestricted]
Enables caller ID.
Not Configured = Privacy is determined according to the Caller ID
table (see Configuring Caller Display Information on page 268).
[0] Allowed = Sends Caller ID information when a call is made using
these destination/source prefixes.
[1] Restricted = Restricts Caller ID information for these prefixes.
Notes:
This field is applicable only to number manipulation tables for source
phone number manipulation.
If this field is set to Restricted and the 'Asserted Identity Mode'
(AssertedIdMode) parameter is set to Add P-Asserted-Identity, the
From header in the INVITE message includes the following: From:
'anonymous' <sip: anonymous@anonymous.invalid> and 'privacy:
id' header.
21.3 Manipulating Number Prefix
The device supports a notation for adding a prefix where part of the prefix is first extracted
from a user-defined location in the original destination or source number. This notation is
entered in the 'Prefix to Add' field in the Number Manipulation tables (see 'Configuring
Source/Destination Number Manipulation' on page 209): x[n,l]y...
where,
x = any number of characters/digits to add at the beginning of the number (i.e. first
digits in the prefix).
[n,l] = defines the location in the original destination or source number where the digits
y are added:
n = location (number of digits counted from the left of the number) of a specific
string in the original destination or source number.
l = number of digits that this string includes.
y = prefix to add at the specified location.
For example, assume that you want to manipulate an incoming IP call with destination
number +5492028888888 (area code 202 and phone number 8888888) to the number
0202158888888. To perform such a manipulation, the following configuration is required in
the Number Manipulation table:
1. The following notation is used in the 'Prefix to Add' field:
0[5,3]15
where,
0 is the number to add at the beginning of the original destination number.
[5,3] denotes a string that is located after (and including) the fifth character (i.e.,
the first '2' in the example) of the original destination number, and its length being
three digits (i.e., the area code 202, in the example).
15 is the number to add immediately after the string denoted by [5,3] - in other
words, 15 is added after (i.e. to the right of) the digits 202.
2. The first seven digits from the left are removed from the original number, by entering
"7" in the 'Stripped Digits From Left' field.

Table of Contents

Other manuals for AudioCodes MediaPack MP-118

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MediaPack MP-118 and is the answer not in the manual?

AudioCodes MediaPack MP-118 Specifications

General IconGeneral
CategoryGateway
Analog Ports8 FXS ports
Voice CodecsG.711, G.723.1, G.726, G.729A/B
Operating Temperature0°C to 40°C (32°F to 104°F)
Storage Temperature-20°C to 70°C (-4°F to 158°F)
ProtocolsSIP, MGCP, H.323
ModelAudioCodes MediaPack MP-118
Fax SupportT.38
ManagementWeb-based, SNMP, CLI
SecuritySRTP, TLS, HTTPS
Power SupplyAC 100-240V, 50-60Hz
Humidity10% to 90%, non-condensing
Network Interfaces2 x 10/100Base-T Ethernet

Related product manuals