EasyManuals Logo

AudioCodes MediaPack MP-118 User Manual

AudioCodes MediaPack MP-118
584 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #509 background imageLoading...
Page #509 background image
Version 6.6 509 MP-11x & MP-124
User's Manual 43. Configuration Parameters Reference
Parameter Description
RTP and for T38 must be different. Therefore, set the
T38UseRTPPort parameter to 0.
Web/EMS: T.38 Max Datagram
Size
[T38MaxDatagramSize]
Defines the maximum size of a T.38 datagram that the device
can receive. This value is included in the outgoing SDP when
T.38 is used.
The valid range is 120 to 600. The default is 238.
Web/EMS: T38 Fax Max Buffer
[T38FaxMaxBufferSize]
Defines the maximum size (in bytes) of the device's T.38 buffer.
This value is included in the outgoing SDP when T.38 is used
for fax relay over IP.
The valid range is 500 to 3000. The default is 1024.
Web: Detect Fax on Answer Tone
EMS: Enables Detection of FAX on
Answer Tone
[DetFaxOnAnswerTone]
Determines when the device initiates a T.38 session for fax
transmission.
[0] Initiate T.38 on Preamble = (Default) The device to which
the called fax is connected initiates a T.38 session on
receiving HDLC Preamble signal from the fax.
[1] Initiate T.38 on CED = The device to which the called fax
is connected initiates a T.38 session on receiving a CED
answer tone from the fax. This option can only be used to
relay fax signals, as the device sends T.38 Re-INVITE on
detection of any fax/modem Answer tone (2100 Hz,
amplitude modulated 2100 Hz, or 2100 Hz with phase
reversals). The modem signal fails when using T.38 for fax
relay.
Note: This parameters is applicable only if the parameter
IsFaxUsed is set to 1 (T.38 Relay) or 3 (Fax Fallback).
Web: T38 Fax Session Immediate
Start
[T38FaxSessionImmediateStart]
Enables fax transmission of T.38 "no-signal" packets to the
terminating fax machine.
[0] Disable (default)
[1] Immediate Start on Fax = Device activates T.38 fax relay
upon receipt of a re-INVITE with T.38 only in the SDP.
[2] Immediate Start on Fax & Voice = Device activates T.38
fax relay upon receipt of a re-INVITE with T.38 and audio
media in the SDP.
This parameter is used for transmission from fax machines
connected to the device and located inside a NAT. Generally,
the firewall blocks T.38 (and other) packets received from the
WAN, unless the device behind NAT sends at least one IP
packet from the LAN to the WAN through the firewall. If the
firewall blocks T.38 packets sent from the termination IP fax, the
fax fails.
To overcome this, the device sends No-Op (“no-signal”) packets
to open a pinhole in the NAT for the answering fax machine.
The originating fax does not wait for an answer, but immediately
starts sending T.38 packets to the terminating fax machine.
Note: To enable No-Op packet transmission, use the
NoOpEnable and NoOpInterval parameters.

Table of Contents

Other manuals for AudioCodes MediaPack MP-118

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MediaPack MP-118 and is the answer not in the manual?

AudioCodes MediaPack MP-118 Specifications

General IconGeneral
CategoryGateway
Analog Ports8 FXS ports
Voice CodecsG.711, G.723.1, G.726, G.729A/B
Operating Temperature0°C to 40°C (32°F to 104°F)
Storage Temperature-20°C to 70°C (-4°F to 158°F)
ProtocolsSIP, MGCP, H.323
ModelAudioCodes MediaPack MP-118
Fax SupportT.38
ManagementWeb-based, SNMP, CLI
SecuritySRTP, TLS, HTTPS
Power SupplyAC 100-240V, 50-60Hz
Humidity10% to 90%, non-condensing
Network Interfaces2 x 10/100Base-T Ethernet

Related product manuals