AUMA Aumatic AC 01.1 User Manual

Page
7.7.6 Derivative gain Kd setting 64
7.7.7 Internal process setpoint setting 65
7.7.8 Behaviour on loss of the process setpoint (wire break monitoring) 66
7.7.9 Inverse operation setting 66
7.7.10 Travel limitation 67
7.7.11 Reaction monitoring setting 68
7.7.12 Input range of process setpoint E1: view 69
7.7.13 Input range of process variable E4: view/edit 69
7.8 Stepping mode (option) 70
7.8.1 Display indication: enable view 70
7.8.2 Stepping mode: switch on or off 71
7.8.3 Stepping range setting (start and end of stepping mode) 71
7.8.4 ON and OFF times setting 72
7.9 Local controls enable function (option) 73
7.9.1 Selector switch functions: enable/disable 73
7.10 EMERGENCY STOP function (option) 75
7.10.1 Description of the functions 75
7.10.2 Feedback signals on the display 76
7.10.3 Feedback signals setting via output contacts 76
7.10.4 Feedback signal setting via LEDs 76
7.11 Profibus DP interface (option) 77
7.11.1 Bus address setting (Slaveaddress) 77
7.12 Redundant bus connection with component redundancy (option) 78
7.12.1 Configuration check for the second fieldbus interface 78
7.12.2 Second fieldbus interface setting 78
7.13 Profibus DP-V1 services (option) 79
7.14 External inputs for bus (option) 80
7.14.1 Signals assignation for operation commands 80
7.15 Combination fieldbus/standard interface (option) 83
7.16 Monitoring and failure functions 84
7.16.1 Torque monitoring 84
7.16.2 Motor protection (thermal monitoring) 85
7.16.3 Monitoring of the max. number of starts per hour and max. running time per hour 86
7.16.4 Operating time monitoring 88
7.16.5 Reaction monitoring 89
7.16.6 Phase failure monitoring 90
8 Corrective action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8.1 Fault indications and warning indications 91
8.1.1 Status indication S0 – faults and warnings 91
8.1.2 Status indication S1 – fault 92
8.1.3 Status indication S2 – warnings 92
8.1.4 Status indication S3 – causes for not ready remote 94
8.2 Diagnostics 95
8.2.1 Operating data logging 95
8.2.2 Diagnostic indications (D) via the display 97
8.3 Troubleshooting 107
8.3.1 Problems with position feedback/indication E2 (from actuator) 107
8.3.2 Display hardly readable or illegible 107
8.3.3 Actuator does not run 107
8.3.4 Actuator does only operate from local 107
8.3.5 Actuator is not switched off by limit seating in direction CLOSE or OPEN 107
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Parameter index and indications on the display . . . . . . . . . . . . . . . . . . 109
Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
4
Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Profibus DP Manual

AUMA Aumatic AC 01.1 Specifications

General

Brand	AUMA
Model	Aumatic AC 01.1
Category	Control Unit
Language	English