Barco DP2K SLP Series Service Manual

R5906848 /04 DP2K SLP Series 21
Pressing the Sleep button in Standby mode for 3 seconds puts the projector in Sleep mode. In case the
projector is processing the after cooling cycle then the projector goes in Sleep mode after finishing the after
cooling cycle.
Pressing the Sleep button in Sleep mode for 3 seconds will awake the projector. The status light will blink for a
few seconds (booting up all inactive boards) and then lights up continuously.
Enter or leave Sleep mode can also be done via 2 dedicated projector command (USB/Ethernet), or via two
predefined Macros (not editable) with GPIO of the Cinema Controller (not the GPIO of the ICMP), or via the
Communicator.
The projector always boots up in the same mode (E.g. Standby or Sleep) as it was switched OFF.
The Sleep button is disabled if the Light Source is on.
2.4 Spare parts for DP2K-SLP Series
Up to date information regarding spare parts for DP2K-SLP Series
Barco continuously improves its service procedures for the customer. Managing spare parts is one of the key
processes. The spare parts list is subject to change. No spare parts list is included in this manual to ensure
that no spare parts are ordered based upon outdated information. Up to date information regarding spare
parts, and much more, is available on Barco's web site http://www.barco.com. Go to myBarco log in and enter
your credentials. Select your market and product and click on the product page on Technical support. The
Spare parts tab becomes available.
2.5 Projector block diagrams
Signal Backplane diagram
Switch 1
Switch 2
P
Switch 4
Switch 3
J15 - FANS LENSSIDE / PUMP
J17 - LENS M OTORS
J281 - CATEYE
J18 - FANS LAMPSIDE / PUMP
J102 - J103 - J 104 - J105
J102 - J103 - J 104 - J105
B3244373
LPS RELAY
25A
J799
J263
J11 - AMB TEMP SENSOR
In Harbin A-series
Not in Harbin A
Mains Filt er
25A
B3058365
Projector ID
J291
J292 J264
J19
J16
Pump
J18
Projection
Lens
R7681044 - R7860042
Button Module
Electronics Box
R76810392 - R7860108
Cinema Controller
Signal Backplane
DCI SECURITY
R765310
R782202
Tail Light
Switched Mode
Power Supply
R7681041 - R7860037
Engine
R7681040 - R7860036
Motorized Lens
Lens Shift L/R
Lens Shift U/D
J100 - J101
J100 - J101
J200 - J201 J400 - J402
J802
J12
J700 - J701 - J702 J700 - J701 - J702
J502
J502
Modular Formatter Green
Modular Formatter Blue
Modular Formatter Red
R76810435 - R7860040 R76810436 - R7860041 R76810432 - R7860039
R765355 - R782232
3D Controller
DMD Front Temperature Peltier Back DMD Back Temperature Peltier Front DMD Block Temperature
RED
J1 - J2
J7
J250 J253 J270 J273 J276
DMD Front Temperature Peltier Back DMD Back Temperature Peltier Front DMD Block Temperature
BLUE
J5 - J6
J9
J252 J255 J272 J275 J278
Light Sensor
R7681049 - R7860045
J277 J274 J271 J254 J251
J8
J3 - J4
GREEN
J283 J279 J14
DMD Block Temperature Peltier Front DMD Back Temperature Peltier Back DMD Front Temperature
(see sheet 1 or 2)
062J01J
J261
J262
J30
J282
Mains Sw itch & Fuse
35J 25J 15J 05J
J15
Not in Harbin A Not in Harbin A
YE OR B R R D
Not in Harbin A
8S/10S Laser Light Source
2
1
R7681061
J200 - J201
ICMP
B324437 is replaced by B3244373 in GarreS
TI ICP + HDSDI
R765582(5) +
R765534 - R782327
or altern
atively:
Image 2-8
General

Barco DP2K SLP Series Specifications

General

Brand	Barco
Model	DP2K SLP Series
Category	Projector
Language	English