Bosch IRIS-Net - Page 941

To Next Page

To Previous Page

Ship Alarm 8

Ship Alarm 9

Ship Alarm 10

Ship Alarm 11

Ship Alarm 12

Ship Alarm 13

Ship Alarm 14

Ship Alarm 15

Ship Alarm 16

Ship Alarm 17

SILENCE -

Pagings Dialog

This dialog allows the configuration of pagings (e.g. alarm or EVAC messags) with dynamic or static destinations.

IRIS-Net PAVIRO | en 941

Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956

Main Page

Table of Contents3
Table of Contents | en4
Notes on the IRIS-Net Documentation5
Preface5
- IRIS-Net System Requirements6
- Installation6
- IRIS-Net Directory Structure6
Basics of IRIS-NET6
- Controls7
- Documentation7
- Driver7
- Firmware7
- Speaker Files8
- User Controls9
- Speaker Settings9
- Tools9
- Creating a New Project10
Introduction10
- How to Edit an Existing Project?13
- Going On-Line13
- Ethernet On-Line Dialog14
- CAN On-Line Dialog15
- Object List18
- Object Bar Categories18
- Adding Devices18
IRIS-Net Objects18
- Adding Controls20
- Adding Interfaces20
- Button Controls21
- Parameter Controls21
- Display Controls22
- Advanced Controls22
- Special Controls24
- How to Configure a Control24
- Adding User Controls25
- RCM-24 User Controls26
- RCM-26 User Controls28
- RCM-28 User Controls30
- RCM General User Controls31
- Matrix User Controls35
- Interface User Controls36
- Miscellaneous User Controls37
- EOL User Controls37
- How to Configure a User Control38
- Adding Graphics39
- Adding Textboxes40
- Using Groups41
- Connections43
- Editing Object Visibility44
- Editing Project Info45
- Software Update45
How to45
- Edit Application Settings46
- Using the SPL Calculator47
- Limiter Threshold Calculator48
- Using the Event Scheduler49
- Holiday53
- Macros55
- Using the Macro Editor55
- Triggers57
- Conditions60
- Timed Condition62
- Using the Scene Editor64
- Searching/Configuring Devices on the Ethernet65
- Editing Network Settings66
- Searching OMNEO-Devices on the Ethernet66
- Event Logging Setup69
- Changing Available Devices70
- Remote Control Network / Interface70
- Connecting an UCC1 USB-CAN Converter to the PC74
- Setting up a Remote Amplifier System74
- Address Setting74
- Setting up a Remote Amplifier System Using a UCC1 USB-CAN Converter74
- Set CAN Baud Rate75
- Main Window77
Reference77
- Menus, Commands and Symbol Bar78
- Menu “Configuration”80
- Menu “Tools”80
- Pushbutton83
- Remote Amps UI88
- Single Channel Group Dialog (DSPUI)89
- Rcm26Remoteampsui92
- Rcm26Dspui93
- Master EQUI X Band97
- System Crossover_X Way97
- N8000_Geq_Xway98
- N8000_Lsc_Xway_Mono99
- N8000_Peq_Xband (_Mono)99
- N8000_Tonecontrol_Mono100
- N8000_Tonegenerator_Mono100
- N8000_Delay_Xms100
Remote Amplifier101
P-Series101
- Remote Power Amps102
- Checking/Editing the Configuration103
- Testing the Connected Loudspeaker Systems104
- Overview of All Amps Used in a Project105
- Amplifier Control Panel107
- Control Functions111
- Setup & Control111
- Jobs115
- Dsp119
- Flow Diagram Selector119
- Flow Diagram119
- Function Blocks120
- Routing Block121
- Channel EQ Block121
- Crossover Block121
- Level Block121
- Store / Recall / Preview122
- Output Block122
- Status Indication122
- Dynamics Block122
- Import / Export of Preset Files123
- Import of EV RACE Files123
- Master Eq124
- Graphics Display Indication125
- Channel Selection125
- Filter Parameters126
- Filter Editing Via “Mouse Movement” in the Graphics Display127
- Master Delay127
- Channel Parameters127
- Channel Identification128
- Channel Eq128
- Editing Delays by Dragging the Mouse in the Graphics Display128
- General Parameters128
- Filter Editing Via Mouse Movement in the Graphics Display131
- X-Over131
- Editing X-Over Filters by Dragging the Mouse in the Graphics Display134
- Dynamics134
- Speaker138
- Indication on the Graphic Display138
- Load139
- Parameters for Impedance Measurement141
- Supervision & Test141
- Control Inputs and Control Outputs142
- Test Generator Parameters142
- Detailed Explanation of Individual Fault Indications143
- Error Detection143
- System Examples145
- Demo System Small145
- RS-232 Protocol for EV P-Series154
- General Dsp Parameter Description162
- Dsp Parameter Index Table163
- Control Inputs - GPI Functions166
- Job Codes - Receive Functions166
- Control Outputs - Gpo Functions168
- Job Codes - Transmit Functions168
- Firmware Upgrade170
- How to Upgrade the Firmware171
- Additional Notes Concerning a Firmware Upgrade174
- Using RCM-26 Remote Amplifiers176
- Remote Amplifiers177
- Dynacord Powerh Serie177
- Electro-Voice Tour Grade Serie177
- Config & Info182
- Amplifier Info182
- Amplifier Setup183
- Digital Input183
- Switching Audio Inputs Automatically184
- Amplifier & Channel Labels184
- Control Port185
- Control Outputs185
- Input and Receive Job Function188
- Output and Transmit Job Conditions189
- Switching Sample Rate195
- Preset after Startup195
- Fir-Filter206
- FIR Filter Design208
- Limiters209
- Peak Limiter Parameters210
- Thermal Limiter Parameters210
- Indications211
- Editing Limiter Parameters by Dragging Mouse in the Graphics Display211
- State/Error Flags231
- Device State Flags231
- Input Channel State Flags232
- Output Channel State Flags232
Rcm-28243
DIGITAL SOUND PROCESSOR DX38 Digital Sound Processor DSP244
Rcm-810288
Rev Wireless Microphone System307
Introduction307
REV Device308
REV Control Panel308
Setup & Control310
Digital Matrix315
Netmax N8000 System Controller315
P 64 Digital Matrix339
N8000 and P 64363
Touch Panels Tpi-5529
Tpi-8/Tpi-12540
Dsp 600 Fir-Tune603
Dx46 FIR-DRIVE649
Dx46 and DSP 600694
Updating the Firmware708
Pws Programmable Wall Station710
PWS Device710
Operation711
Configuration711
Button Types714
Channel Selection715
Promatrix 8000719
DPM 8016 Paging Manager722
DPC 8000 Call Station795
PMX-CSK Call Station Kit810
DPA 8000 Power Amplifier817
Control Panel818
DCS Digital Control System825
Promatrix 6000834
Pmx-4Cr12834
Pmx-4R24888
Pmx-15Cst893
Pmx-2P500906
Pmx-Csk906
Paviro911
Pva-4Cr12911
Pva-4R24965
Pva-15Cst969
Pva-Csk982
Pva-2P500987

Bosch IRIS-Net - Page 941

Table of Contents

Related product manuals