II- INSTALLAZIONE
Ejection confirmation (Eject confirmation)................................................................................................................................................................47
Container full (Full bin).............................................................................................................................................................................................47
Impulse encoder (Encoder)......................................................................................................................................................................................47
Alarm reset (Reset)..................................................................................................................................................................................................47
Inhibition ..................................................................................................................................................................................................................47
Air pressure sensor..................................................................................................................................................................................................47
Container absent (Bin absent) .................................................................................................................................................................................47
OPERATING INSTRUCTIONS ..............................................................................................................................................................................................48
LIST OF PRELIMINARY CHECKS.........................................................................................................................................................................................48
OPERATIONS DURING USE AND AREAS OF COMPETENCE...........................................................................................................................................48
CONTROLS AND INDICATORS............................................................................................................................................................................................49
Power switch...................................................................................................................................................................................................................49
Control panel of the probe/electronics unit......................................................................................................................................................................49
Acoustical indicators................................................................................................................................................................................................49
Controls ...................................................................................................................................................................................................................50
Conveyor Control System power supply unit control panel .............................................................................................................................................50
Visible/audible alarm signalling device............................................................................................................................................................................51
SWITCHING ON THE METAL DETECTOR...........................................................................................................................................................................51
Checking the safety features ..........................................................................................................................................................................................51
Signals at power-up ........................................................................................................................................................................................................52
SIGNALS GIVEN DURING USE ............................................................................................................................................................................................52
Indication of the received signal......................................................................................................................................................................................52
Checking for environmental electromagnetic interference...............................................................................................................................................53
Display Messages...........................................................................................................................................................................................................53
DISPLAY OF THE STATUS OF THE METAL DETECTOR....................................................................................................................................................54
USE OF THE CONVEYOR BELT ..........................................................................................................................................................................................54
Starting/stopping the conveyor belt.................................................................................................................................................................................54
Adjustment of the belt speed ..........................................................................................................................................................................................54
Emergency button...........................................................................................................................................................................................................55
Automatic stop................................................................................................................................................................................................................55
ALARM RESET......................................................................................................................................................................................................................55
AUTOMATIC OPERATION USING A BAR-CODE READER.................................................................................................................................................55
PHOTOCELL SELF-DIAGNOSIS...........................................................................................................................................................................................56
PROGRAMMING THE METAL DETECTOR ACCORDING TO THE KIND OF PRODUCT....................................................................................................56
Procedure for minimising the "product effect"..........................................................................................................................................................56
ANALYSIS MODE SELECTION CRITERIA ...........................................................................................................................................................................58
SENSITIVITY CHECK WITH REFERENCE SAMPLE ...........................................................................................................................................................59
Test using a sample defined by the customer.................................................................................................................................................................59
Test using a CEIA sample ..............................................................................................................................................................................................59
Periodic test management .......................................................................................................................................................................................59
Test procedure ........................................................................................................................................................................................................59
PROGRAMMING...................................................................................................................................................................................................................61
GENERAL POINTS ON PROGRAMMING.............................................................................................................................................................................61
PROGRAMMING INSTRUCTION..........................................................................................................................................................................................63
Products menu................................................................................................................................................................................................................63
Autolearn menu ..............................................................................................................................................................................................................64
Detection menu...............................................................................................................................................................................................................65
Ejection menu.................................................................................................................................................................................................................66
Ejection time menu ..................................................................................................................................................................................................67
Counters menu ...............................................................................................................................................................................................................68
Barcode reader menu .....................................................................................................................................................................................................68
THS Configuration menu.................................................................................................................................................................................................70
Date settings menu..................................................................................................................................................................................................72
Change Password menu..........................................................................................................................................................................................73
ALM Configuration menu ................................................................................................................................................................................................73
I/O Status menu..............................................................................................................................................................................................................77
MD Test menu ................................................................................................................................................................................................................77
Print menu ...............................................................................................................................................................................................................78
Print report menu.....................................................................................................................................................................................................79
Quality Control menu (Q.C.Report).................................................................................................................................................................................80
Test Sensitivity menu (Test sensitiv.).......................................................................................................................................................................80
Commands accessible only in Remote Programming.....................................................................................................................................................81
REMOTE PROGRAMMING VIA SERIAL LINK......................................................................................................................................................................82
Communication parameter settings: ...............................................................................................................................................................................82
Entering remote programming ........................................................................................................................................................................................82
Connecting to a metal detector (via RS 232) ...........................................................................................................................................................82
Long-distance connection to a single metal detector (via RS 485) ..........................................................................................................................82
Network connection (via RS 485).............................................................................................................................................................................82
Connecting to a metal detector in a network............................................................................................................................................................83
3.13.3 - Displaying a parameter setting ...................................................................................................................................................................83
3.13.4 - Changing a parameter setting.....................................................................................................................................................................83
3.13.5 - Executing a function ...................................................................................................................................................................................83
MAINTENANCE.....................................................................................................................................................................................................................84
PERIODIC MAINTENANCE...................................................................................................................................................................................................84
SELF-DIAGNOSIS.................................................................................................................................................................................................................85
STORAGE .............................................................................................................................................................................................................................86
TRANSPORT AND MOVEMENT OF THE CONVEYOR BELT..............................................................................................................................................86
ADJUSTMENT OF CONVEYOR BELT TENSION .................................................................................................................................................................86
Replacing the belt ...........................................................................................................................................................................................................87
DISPOSAL OF THE DEVICE AND OF CONSUMABLES WITH ENVIRONMENTAL IMPACT ..............................................................................................87
FUSES...................................................................................................................................................................................................................................87
TROUBLESHOOTING...........................................................................................................................................................................................................87
Self-resetting protections .........................................................................................................................................................................................87
Replacing Card SCD.......................................................................................................................................................................................................89
Procedure................................................................................................................................................................................................................89
CHECKING ENVIRONMENTAL ELECTROMAGNETIC INTERFERENCE............................................................................................................................90
APPENDICES........................................................................................................................................................................................................................91
DECLARATION OF CONFORMITY CE.................................................................................................................................................................................91
SPARE PARTS, OPTIONS AND ACCESSORIES.................................................................................................................................................................92
Ordering spare parts.......................................................................................................................................................................................................92
THS standard model / THS/3F........................................................................................................................................................................................92
THS /A............................................................................................................................................................................................................................92
To Next Page
Loading...
