To Next PageTo Next PageWhat does a negative zero mean on Ecotech Measuring Instruments?
If your Ecotech Measuring Instruments are showing a negative zero, it indicates that the internal zero air converter is less efficient than the external zero air supplied. Perform a leak test and check that the internal zero air supply is equipped with a functioning CO-CO2 converter.
What to do if the sample pressure is too high or low on Ecotech Acoem Serinus 30?
To resolve a 'Sample pressure too high or low' error on Ecotech Measuring Instruments, perform a pressure calibration.
What to do if 12 Voltage supply failure in Ecotech Measuring Instruments?
If the 12 Voltage supply fails in your Ecotech Measuring Instruments, the power supply has likely failed and needs to be replaced.
General| Gas Measured | Carbon Monoxide (CO) |
|---|---|
| Measurement Range | 0-50 ppm |
| Resolution | 0.01 ppm |
| Linearity | ±1% of full scale |
| Power Requirements | 100-240 VAC, 50/60 Hz |
| Response Time | <60 seconds |
| Operating Temperature | 0 to 40°C |
| Operating Humidity Range | 0% to 95% RH (non-condensing) |
| Outputs | RS232 |
Details critical safety precautions for operating and maintaining the instrument.
Provides a general overview of the Ecotech Serinus 30 Carbon Monoxide Analyser.
Details the technical specifications of the Serinus 30 analyser.
Explains the principles and techniques used for CO measurement.
Describes the Kalman filter's role in response time and noise reduction.
Details the calibration valve manifold's function in switching gas sources.
Describes the sample filter holder and its particulate filter.
Explains the CO-CO2 catalytic converter's function and operation.
Describes the measurement cell and its internal components.
Details the main controller PCA which manages instrument processes.
Describes the specially designed pneumatic tubing used in the instrument.
Details the connections and components on the rear panel.
Outlines the instrument's communication interfaces and capabilities.
Guidance on performing initial checks after receiving the instrument.
Key considerations and recommendations for instrument installation.
Procedures for preparing the instrument for monitoring after installation.
Conditions required for Serinus 30 to meet U.S. EPA reference method approval.
Conditions for meeting EN requirements for continuous ambient air quality monitoring.
Instructions for safely transporting and storing the instrument.
Describes the instrument's warm-up procedure and activities.
Explains the continuous sample cycle and background measurement process.
Provides general information on operating the instrument.
Overview of the instrument's menu system and screen navigation.
Details RS232 communication for data access and connection to loggers.
Information on connecting and downloading data via USB.
Setup and configuration for TCP/IP network access to the instrument.
Describes analog and digital I/O port signals for external devices.
Instructions for configuring internal data logging to a USB memory stick.
Guide to using Airodis software for data download and remote operation.
Details on connecting and controlling the instrument via an Android app.
Provides a brief overview of the calibration system and procedures.
Instructions for performing pressure calibration on the instrument.
Procedure for manually performing a background measurement.
Steps to perform zero calibration to adjust instrument readings.
Procedure for performing span calibration at the upper measurement range.
Details on performing precision checks to monitor instrument response.
Procedure to determine linear response across the instrument's measurement range.
Calibrates the flow rate generated by the internal pump.
Information on using internal pressurised calibration valves.
Specific safety advice for personnel performing service on the instrument.
Lists the equipment required for general maintenance tasks.
Recommended schedule for routine maintenance tasks.
Detailed steps for performing essential maintenance procedures.
Information on accessing the bootloader for advanced functions.
Diagnosing and resolving issues related to instrument flow faults.
Troubleshooting steps for noisy or unstable measurement readings.
Detailed diagnostic procedure for flow fault alarms.
Diagnostic procedure for addressing noisy or unstable readings.
Troubleshooting steps for cell temperature failure.
Troubleshooting steps for mirror temperature failure.
Guidance on troubleshooting USB memory stick related issues.
Information on preparing support files for Ecotech technical assistance.
Details on the dual sample filter option.
Information on the optional network port feature.
Instructions for installing the instrument using a rack mount kit.
Details on the internal pump option and its components.
Information on the trace level instrument option for low-level CO detection.
Details on the optional external CO2 sensor for CO2 measurements.
List of assorted fittings, tubing, and tools included in the accessories kit.
List of parts included in the maintenance kit for annual servicing.
List of consumable parts requiring replacement over the instrument's lifespan.
Reference list of Serinus 30 components and their part numbers.
Schematic showing the instrument's pneumatic connections.
Schematic illustrating the block wiring of the instrument's components.
Detailed parts list and diagram for the measurement cell assembly.
Diagram and parts list for the source timing assembly.
Diagram and parts list for the calibration manifold assembly.
Diagram and parts list for the valve assembly.
Exploded view and parts list for the high pressure valve assembly.
Diagram and parts list for the sample filter holder assembly.
Diagram and parts list for the CO-CO2 converter assembly.
Details the packet format for advanced protocol commands and responses.
Lists and explains commands available under the advanced protocol.
Describes the command format for the EC9800 protocol subset.
Lists and explains basic commands for the EC9800 protocol.
Details the command format for the Bayern-Hessen network protocol.
Lists and explains commands for the Bayern-Hessen protocol.
Describes the command format for the limited Modbus implementation.
Lists and explains Modbus commands supported by the Serinus.
