FAAC A1000 - Page 110

116 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

A1000 110 532210 04 - Rev.A



Table of Contents

Default Chapter3
- EC Declaration of Conformity of a Machine3
- EC Declaration of Conformity3
- Declaration of Incorporation of Partly Completed Machinery4
- Declaration of Incorporation for Partly Completed Machinery4
- Table of Contents5
1 Introduction to the Manual7
- Safety Recommendations7
- Meaning of the Symbols Used8
- Symbols: Notes and Warnings on the Instructions8
- Symbols: Tools (Type and Size)8
- Symbols: Safety Signs and Symbols (en ISO 7010)9
- Symbols: Markings on Product9
- Symbols: Personal Protective Equipment9
- Symbols: Markings on Packaging9
2 Automation A100010
- Intended Use10
  - Limitations for Use10
- Unauthorised Use10
- Identification Plate11
- Technical Specifications A100012
- Technical Specifications12
- Types of System Supplied13
3 Inspection and Preparation16
- Preliminary Inspection16
- Arrangement of Electrical Cables16
4 Transport and Receipt of the Goods17
- Handle Packages17
- Unpack and Handle17
5 Cutting the Profiles18
- Profile Cutting Measurements18
6 Assembling the Head Section19
- Assembling the Components20
7 Assembling the A1000 Cs Frame25
- Entry with TK50 Profiles25
- Entry Door with TK20 Profiles26
8 Installing the Head Section28
- Preliminary Operations28
- Fastening to the Wall28
9 Installing the Leaves29
- Mounting the Lower Shoes29
- Mount Profiles on the Leaves30
- Mount the Lower Sweeper30
  - Glass Leaves30
- Installing the Leaves30
- Adjusting the Leaves and Carriages31
10 Installing the Glass Leaves32
- Mounting the Brushes34
11 Assemble the Belt, Casing and Accessories35
- Mounting the Belt35
  - Adjusting the Belt37
- Belt Tensioning38
- A1000 Belt Tensioning (Measurements in MM)38
- Adjusting the Mechanical Stops39
- Mounting the Side Profiles40
- Installing the Casing Brackets40
- Fitting the Cover41
- Installing the XB LOCK Motor Block42
- Adjusting the XB LOCK Motor Block42
- Mounting the Cable Gland Guides43
12 Electronics Installation E1Sl44
- E1SL Electronic Module44
  - E1SL Electronic Board44
- Leds on the Board45
- Terminal Boards and Connectors46
- Motor and Encoder48
- XB LOCK Motor Block and Monitoring (OPTIONAL)48
- XV1-XDT1 EXIT and Entry Detectors49
- XDT1 Exit Detectors and 2 XDT1 ENTRY Detectors50
- XBFA Detectors for Safety in OPENING51
- J9 - XFA Button Photocells52
- J7 - Inputs52
- J22 - Configurable Outputs52
13 Startup53
- Preliminary Checks Prior to Commissioning53
- Switching on and System SETUP53
  - Checks Following SETUP53
  - Saving the Configuration53
- Basic / Advanced Programming54
- BASIC Programming Fw Version 3.0 or Later55
- ADVANCED Programming Fw Version 3.0 or Later58
14 System Functionality/Configurations62
- Operating Mode62
- Inputs Configuration63
- Configuration of J22 Outputs65
- Obstacle Detection65
- Anti-Intrusion and PULL&GO65
- ELASTIC Kit65
- Energy Saving Function65
  - Activating the Energy Saving Function65
- Low Energy Function During Closing and OPENING66
  - Setting the Low Energy Function During Closing CS CF66
  - Setting the Low Energy Function During Opening os of66
15 Diagnostics66
- System Diagnostics: Alerts, Errors66
- Max. Speed Settings in Low Energy Mode66
- Status of the Automation66
- Errors67
- Warnings68
- AUX Errors69
- Troubleshooting70
- Troubleshooting Guide70
16 Operations on the Board71
- Setup71
  - How to Perform Setup from Board71
- Reset71
  - When Is Reset Necessary71
  - How to Perform a RESET from the Board71
- Restoring Factory Status71
  - When Is Restore Necessary71
  - How to Perform Restore71
- Updating (UPLOAD)72
- Download72
- Updating Functions (UPLOAD) from USB72
- Download to USB Functions72
- Firmware and Programming File Names72
- BOOTLOADER Errors73
17 Intercom (Canbus)74
Evo74
- Intermode75
- Interlock75
  - Interlock with no Memory75
  - Interlock with Memory76
18 Fw Version 1.2 or Later77
- Assembly and Testing77
- Special Functions78
19 Ks Evo79
- Assembly and Testing79
- Errors80
- Warnings81
- Firmware Version81
20 Fw Version 3.0 or Later82
- Assembly and Testing82
- Switching on and Use82
- Home Page83
- Reset - Lock/Release SDKEVO83
- Password83
- Selection MENU84
- Function MENU85
- FUNCTIONS Menu86
21 Maintenance97
- Calculation Estimate of Cycles Performed97
  - Routine Maintenance97
  - Periodic Replacements97
- Maintenance Programme and Periodic Replacements97
- Maintenance Technician Safety98
- Replacements98
- Cleaning100
- Functional Checks100
22 Waste Disposal100
23 Annexes to A1000101
- A1000 Automation Weights101
- Positions of Components on the Head Section101
- Installation Diagrams102
- Position of Components on the A1000 Support Profile105

Related product manuals

Preview: FAAC A1400 AIR

FAAC A1400 AIR RD

FAAC A140 AIR Series

Preview: FAAC 950N2

Preview: FAAC 950 N

Preview: FAAC 595

Preview: FAAC 950 BM

Preview: FAAC DAAB MT

Preview: FAAC S2500I CERNIERA

FAAC S2500I CERNIERA