HP Integrity rx4640

Chapter 4
Installing Additional Components and Configuring
Fibre Channel (FC) Boot Configuration
80
0 : Enumerate all Fibre Channel boot devices in the boot option list
1 : Enumerate all Fibre Channel devices
Q : exit with no change
Policy > 1
Drv[2A] Ctrl[2C] Lang[eng] - Options set. Action Required is None
Step 5. Allow the FC devices to be scanned by typing the following command:
Shell> reconnect –r
Step 6. Allow the file systems to be mapped by typing the following command:
Shell> map -r
Device mapping table
fs0 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig11D3A260-CDCC-0
1C2-507B-9E5F8078F531)
fs1 : Acpi(HWP0002,100)/Pci(1|1)/Scsi(Pun0,Lun0)/HD(Part1,Sig55A90000)
fs2 : Acpi(HWP0002,500)/Pci(2|0)/Fibre(WWN21000020375AE714,Lun0)/HD(Part1,Si
gF7D00000)
fs3 : Acpi(HWP0002,500)/Pci(2|0)/Fibre(WWN21000020375A5E5B,Lun0)/HD(Part1,Si
g7D930000)
fs4 : Acpi(HWP0002,600)/Pci(1|0)/Scsi(Pun4,Lun0)/HD(Part1,Sig70BEA120-E7EA-0
1C2-507B-9E5F8078F531)
blk0 : Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)
blk1 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)
blk2 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part1,Sig11D3A260-CDCC-0
1C2-507B-9E5F8078F531)
blk3 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part2,Sig11E8FF20-CDCC-0
1C2-F1B3-12714F758821)
blk4 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part3,Sig2173E520-FDD5-0
1C2-A1F4-04622FD5EC6D)
blk5 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part4,Sig8274F148-6685-1
1D7-8BC4-B6CD81B7B01F)
blk6 : Acpi(HWP0002,100)/Pci(1|0)/Scsi(Pun1,Lun0)/HD(Part5,Sig82757488-6685-1
1D7-8BC4-B6CD81B7B01F)
blk7 : Acpi(HWP0002,100)/Pci(1|1)/Scsi(Pun0,Lun0)
blk8 : Acpi(HWP0002,100)/Pci(1|1)/Scsi(Pun0,Lun0)/HD(Part1,Sig55A90000)
blk9 : Acpi(HWP0002,100)/Pci(1|1)/Scsi(Pun0,Lun0)/HD(Part2,Sig55A90000)
blkA : Acpi(HWP0002,500)/Pci(2|0)/Fibre(WWN21000020375AE714,Lun0)