tagvalue -- Set tag value that selects entries in the snmpTargetAddr table. (ASCII-STR) (p. 632)■
■ [no] snmpv3 only -- Accept only SNMP v3 messages. (p. 629)
■ [no] snmpv3 params -- Configure SNMPv3 Target Parameter entry. (ASCII-STR) (p. 629)
■ user -- Set user that the switch will send messages on behalf. (ASCII-STR) (p. 632)
■ sec-model -- Set security model. (p. 631)
■ sec-model12c < ver1 | ver2c > -- Configure SNMPv3 User entry. (p. 631)
■ message-processing < ver1 | ver2c | ver3 > -- Set message processing model value.
(p. 628)
■ ver3 -- SNMP version 3 security model. (p. 633)
■ message-processing -- Set message processing model value. (p. 628)
■ ver3 < noauth | auth | priv > -- Set security level. (p. 633)
■ [no] snmpv3 restricted-access -- Configure SNMPv1 and SNMPv2c access properties. (p. 630)
■ [no] snmpv3 targetaddress -- Configure SNMPv3 Target Address entry. (ASCII-STR) (p. 632)
■ params -- Set parameter name. (ASCII-STR) (p. 629)
■ ipaddr -- Set IP address of the destination target. (IP-ADDR) (p. 627)
■ addr-mask -- Set range of transport addresses with this mask. (IP-ADDR) (p. 625)
■ filter < None | Debug | All | ... > -- Set log filters. (p. 626)
■ max-msg-size < 484 to 65535 > -- Set maximum message size value; default is 1472. (p.
628)
■ port-mask -- Set range of udp ports with this mask. (TCP/UDP-PORT) (p. 629)
■ retries < 0 to 255 > -- Set retries value; default is 3. (p. 630)
■ taglist -- Set list of values used to select this entry from snmpNotifyTable. (ASCII-STR)
(p. 631)
■ timeout < 0 to 2147483647 > -- Set time-out value; default is 1500. (p. 632)
■ udp-port -- Set UDP port number to which the messages are sent; default is 162.
(TCP/UDP-PORT) (p. 632)
■ ipv6addr -- Set IPv6 address of the destination target. (IPV6-ADDR) (p. 627)
■ addr-mask -- Set range of transport addresses with this mask. (IP-ADDR) (p. 625)
■ filter < None | Debug | All | ... > -- Set log filters. (p. 626)
■ max-msg-size < 484 to 65535 > -- Set maximum message size value; default is 1472. (p.
628)
■ port-mask -- Set range of udp ports with this mask. (TCP/UDP-PORT) (p. 629)
■ retries < 0 to 255 > -- Set retries value; default is 3. (p. 630)
■ taglist -- Set list of values used to select this entry from snmpNotifyTable. (ASCII-STR)
(p. 631)
■ timeout < 0 to 2147483647 > -- Set time-out value; default is 1500. (p. 632)
■ udp-port -- Set UDP port number to which the messages are sent; default is 162.
(TCP/UDP-PORT) (p. 632)
■ [no] snmpv3 user -- Configure SNMPv3 User entry. (p. 632)
■ username -- Set authentication paramaters. (ASCII-STR) (p. 633)
■ auth -- Set authentication paramaters. (p. 625)
■ authpassword -- Set authentication password. (ASCII-STR) (p. 625)
■ priv -- Set Privacy password. (p. 629)
■ privpassword -- Set Privacy password. (ASCII-STR) (p. 630)
■ privprotocol < DES | AES > -- Set privacy protocol. (p. 630)
■ privpassword -- Set Privacy password. (ASCII-STR) (p. 630)
■ authprotocol < MD5 | SHA > -- Set authentication protocol. (p. 625)
■ authpassword -- Set authentication password. (ASCII-STR) (p. 625)
■ priv -- Set Privacy password. (p. 629)
■ privpassword -- Set Privacy password. (ASCII-STR) (p. 630)
■ privprotocol < DES | AES > -- Set privacy protocol. (p. 630)
■ privpassword -- Set Privacy password. (ASCII-STR) (p. 630)
624© 2009 Hewlett-Packard Development Company, L.P.
snmpv3Command Line Interface Reference Guide
To Next Page
Loading...
