HP ProCurve 5400zl User Manual

chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p. 720)■
■ passive -- Configures an ospf interface as passive. (p. 739)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 742)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is 5.
(p. 746)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 749)
■ area -- Specify an OSPF area. (p. 716)
■ area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID) (p. 717)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 719)
■ authentication -- Disable authentication. (p. 717)
■ authentication-key -- Set simple authentication method and key. (p. 717)
■ authentication-key -- OSPF authentication key (maximum 8 characters). (OCTET-STR)
(p. 717)
■ cost < 1 to 65535 > -- Set metric of this interface. (p. 721)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 721)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 725)
■ ip-addr -- Specify the IP address the request is for. (IP-ADDR) (p. 729)
■ area -- Specify an OSPF area. (p. 716)
■ area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID) (p. 717)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 719)
■ authentication -- Disable authentication. (p. 717)
■ authentication-key -- Set simple authentication method and key. (p. 717)
■ authentication-key -- OSPF authentication key (maximum 8 characters). (OCTET-STR)
(p. 717)
■ cost < 1 to 65535 > -- Set metric of this interface. (p. 721)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 721)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 725)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 734)
■ chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p. 720)
■ passive -- Configures an ospf interface as passive. (p. 739)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 742)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is 5.
(p. 746)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 749)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 734)
■ chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p. 720)
■ passive -- Configures an ospf interface as passive. (p. 739)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 742)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is 5. (p.
746)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 749)
■ pim-dense -- Enable/disable/configure PIM-DM protocol on the VLAN interface (p. 739)
■ graft-retry-interval < 1 to 10 > -- Set the interval a PIM router waits for a Graft Ack before
resending a Graft on this interface (p. 725)
■ hello-delay < 0 to 5 > -- Set the maximum time before a triggered PIM Hello message is
transmitted on this interface (p. 725)
■ hello-interval < 5 to 300 > -- Set the frequency at which PIM Hello messages are transmitted
on this interface (p. 725)
■ ip-addr -- Set the source IP address for the PIM-DM packets sent out on this interface (p.
729)
■ any -- Dynamically determine IP address. (p. 716)
■ ip-addr -- Specify IP address. (IP-ADDR) (p. 729)
■ lan-prune-delay -- Turn on/off the LAN Prune Delay Option on this interface (p. 733)
708© 2009 Hewlett-Packard Development Company, L.P.
vlanCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English