HP ProCurve 5400zl

■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ copy config < config1 | config2 | config3 > -- Copy named configuration file. (p. 106)
■ config -- Copy data to specified configuration file. (ASCII-STR) (p. 106)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ pc -- Change CR/LF to PC style. (p. 120)
■ unix -- Change CR/LF to unix style. (p. 131)
■ copy crash-data -- Copy the switch crash data file. (p. 107)
■ card -- Enter single slot identifier. (SLOT-ID-RANGE) (p. 105)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ mm -- Copy from the management card. (p. 119)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
■ xmodem -- Use xmodem on the terminal as the data destination. (p. 135)
■ tftp -- Copy data to a TFTP server. (p. 124)
■ tftp-ip -- Specify TFTP server IPv4 address. (IP-ADDR) (p. 126)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ tftp-ipv6 -- Specify TFTP server IPv6 address. (IPV6-ADDR) (p. 129)
■ filename -- Specify filename for the TFTP transfer. (ASCII-STR) (p. 109)
■ usb -- Copy data to a USB flash drive. (p. 133)
■ filename -- Specify filename for the USB transfer. (ASCII-STR) (p. 109)
97© 2009 Hewlett-Packard Development Company, L.P.
copyCommand Line Interface Reference Guide