Lenze 8200 - Page 8

Contents
8200SHB0199
iii
4 Installation 4-1................................................
4.1 Mechanical installation 4-1............................................
4.1.1 Important notes 4-1........................................
4.1.2 Standard assembly with fixing rails or fixing brackets 4-3..............
4.1.2.1 Types 8201 to 8204 4-3..........................
4.1.2.2 Type 8202-V002 (reduced assembly depth) 4-3..........
4.1.2.3 Types 8211 to 8214 4-4..........................
4.1.2.4 Types 8215 to 8218 4-5..........................
4.1.2.5 Types 8221 to 8227 4-6..........................
4.1.2.6 Types 8241 to 8246 4-7..........................
4.1.3 DIN-rail assembly 4-8.......................................
4.1.3.1 Types 8201 to 8204 4-8..........................
4.1.3.2 Types 8211 to 8214 4-9..........................
4.1.4 Assembly with thermally separated power stage
(”push-through technique”) 4-10................................
4.1.4.1 Types 8215 to 8218 4-11..........................
4.1.4.2 Types 8221 to 8227 4-12..........................
4.1.4.3 Types 8241 to 8246 4-13..........................
4.1.5 Assemblyof the variant 82XX-V003 ”cold plate” 4-14.................
4.1.5.1 General 4-14...................................
4.1.5.2 Demands on the cooler 4-15........................
4.1.5.3 Thermal performance of the system 4-16...............
4.1.5.4 Assembly preparations 4-17........................
4.1.5.5 Assembly of 821X-C-V003 4-18.....................
4.1.5.6 Assembly of 822X-C-V003 4-21.....................
4.1.5.7 Assembly of 824X-C-V003 4-22.....................
4.1.6 Assemblywith mains filter 4-23.................................
4.1.7 Assembly of the analog plug-in module 8279IB 4-24..................
4.2 Electrical installation 4-25.............................................
4.2.1 Operator’s safety 4-25.......................................
4.2.2 Protection of the controllers 4-26...............................
4.2.3 Motor protection 4-26.......................................
4.2.4 Mains types/mains conditions 4-27..............................
4.2.5 Combination with compensation equipment 4-27.....................
4.2.6 Specification of the cables used 4-27.............................
4.2.7 Power connections 4-28......................................
4.2.7.1 Mains connection 4-28............................
4.2.7.2 Motor connection 4-29............................
4.2.7.3 Connection of a brake unit 4-34......................
4.2.7.4 Connection plan 820X 4-35.........................
4.2.7.5 Connection plan 821X 4-36.........................
4.2.7.6 Connection plan 822X/824X 4-37....................
4.2.8 Control connections 4-38.....................................
4.2.8.1 Control cables 4-38..............................
4.2.8.2 Assignment of the control terminals 4-38...............
4.2.8.3 Connection diagrams 4-41.........................
4.2.8.4 Connection diagrams: Analog plug-in module 4-42........
4.3 Installation of a CE-typical drive system 4-43................................
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com