DANGER
CRUSHING HAZARD
• Death or serious injury could result
from being crushed by moving machinery
or by improper set-up on outriggers.
• Ensure all pins and floats are
properly installed and the outrigger
beams are properly extended before
lifting on outriggers.
• Stand clear while outriggers are being
extended or retracted.
7376011087
DANGER
CRUSHING HAZARD
• Death or serious injury could result
from being crushed by moving machinery
or by improper set-up on outriggers.
• Ensure all pins and floats are
properly installed and the outrigger
beams are properly extended before
lifting on outriggers.
• Stand clear while outriggers are being
extended or retracted.
7376011087
THIS CRANE IS NOT INSULATED.
TO AVOID DEATH OR SERIOUS INJURY
Keep ALL parts of the crane, rigging and load at least 20 feet
(6 meters) away from any energized power line. You MUST
follow the OSHA requirements set forth in 29CFR 1926.1407
through 1926.1411.
This crane is not designed or equipped for use within 10 feet
(3 meters) of energized power lines [Refer to 29CFR1926.1410
Table A]. If operation within 10 feet (3 meters) of any power
lines cannot be avoided, the power utility MUST be notified
and the power lines MUST be de-energized and grounded
BEFORE performing any work.
If contact is ever accidentally made with a power line and any
part of this crane, its rigging or load, NEVER touch the crane
or even approach or come near the crane.
Electrocution CAN OCCUR even without direct contact with
the crane.
DANGER
80037260
ELECTROCUTION HAZARD
THIS CRANE IS NOT INSULATED.
TO AVOID DEATH OR SERIOUS INJURY
Keep ALL parts of the crane, rigging and load at least 20 feet
(6 meters) away from any energized power line. You MUST
follow the OSHA requirements set forth in 29CFR 1926.1407
through 1926.1411.
This crane is not designed or equipped for use within 10 feet
(3 meters) of energized power lines [Refer to 29CFR1926.1410
Table A]. If operation within 10 feet (3 meters) of any power
lines cannot be avoided, the power utility MUST be notified
and the power lines MUST be de-energized and grounded
BEFORE performing any work.
If contact is ever accidentally made with a power line and any
part of this crane, its rigging or load, NEVER touch the crane
or even approach or come near the crane.
Electrocution CAN OCCUR even without direct contact with
the crane.
DANGER
80037260
ELECTROCUTION HAZARD
7376102532
Fire from flammable fuel
can cause serious injury
or death.
No smoking, sparks or
open flame during fueling.
DANGER
DIESEL
7376011062G7
D
DANGER
7376102946
To avoid death or serious injury:
Never mix gasoline, alcohol, or gasohol
with diesel fuel. This mixture can cause
an explosion.
G7
Use only ultra low sulfur fuel. Failure to
do so may cause damage to the catalyst.
80021918G7
USE ISO 22241-1
QUALITY DIESEL
EXHAUST FLUID
(DEF) ONLY
2XR 36
2X R11.5
80116980
G7
CUTOUT
To avoid possible engine fault
codes and undesirable
operation, ensure the keyswitch
has been off 2 minutes before
disconnecting batteries.
Disconnect batteries, if machine
will be inactive for over 24
hours.
7376102819
CAUTION
7376102554
Explosive gases can
cause serious injury or
death.
Keep sparks, open flame,
and lighted material away
DANGER
CAUTION
80030034
G7
Hot surface and
gases can cause
serious injury.
Keep clear while
red light is flashing
and allow to cool
before touching.
7376102349
ELECTRONICS DAMAGE
Welding can cause electronic
component damage.
Obtain Manufacturer's
approval before any welding.
See service manual.
CAUTION
G7 80025216
Attention
Special lubricant has been installed in
this component. For more information
please refer to lubrication decal on
Hydraulic Reservoir or lubrication chart
in Operator's Manual.
G7 80025216
Attention
Special lubricant has been installed in
this component. For more information
please refer to lubrication decal on
Hydraulic Reservoir or lubrication chart
in Operator's Manual.
G7
80127100
CAUTION
BATTERY CONNECTION
TO BATTERY
DISCONNECT
SWITCH
To prevent damage to electronics, consult Service Manual before
disconnecting cables. In order: Ensure key switch has been off 2
minutes, Battery disconnect is in the off position, Remove ECM
power fuse, Remove negative cables, Remove positive cables.
TO STARTER (-)
TO ENGINE
BLOCK GROUND
STUD
WIRE 2351WIRE 1358
TO FRAME
GROUND
DISTRIBUTION
BOX
7 POSITION FUSE BOX
WIRES IN
80127149
G7
80A 80A 80A 100A 125A 125A
BATT
DISC
#5 #6 #1274 #2095 #1292 #151
FROM WIRE WIRE WIRE WIRE WIRE WIRE
80127154
G7
NO
PRESSURE
SPRAY
INSIDE BATTERY BOX DOOR
INSIDE HINDGED
FUSE BOX COVER
OUTSIDE HINDGED
FUSE BOX COVER
BATTERY BOX FUSE AND RELAY
80129231
G7
20A
15A
30A
5A
15A
15A
15A
K111 K108 K112
K109 K110
F1 F2 F3 F4 F5 F6 F7
15A
F8
K113
KS2
GND
KS1CCM11 KS1 KS2IOL31
2095 1358
CAN-B J1939 1412/2321 8.5VDC
RESISTOR SPLICE SPLICE SPLICE
D1 D2 D3
15A
10A
10A
5A
15A
F105
F104
F103
F102
F101
15A
F106
F1 - Fused Battery Power
F2 - UE+ Carrier CCM11/IOL31
F3 - Engine ECM Power
F4 - Diagnostic Tool Power
F5 - Cold Weather Power
F6 - Cold Weather Power
F7 - UB+ Carrier CCM11/IOL31
F8 - UB+ Carrier CCM11/IOL31
F101 - DEF Lines Heater Fuse Relay Power
F102 - DEF Lines Heater Fuse Relay Coil
F103 - DEF Supply Module Fused Power
F104 - Aftertreatment Sensor Relay Power
F105 - Starter Lockout Relay Power
F106 - Outrigger light Relay Power
D1 - Pressure Line Heater
D2 - Teturn Line Heater
D3 - Suction Line Heater
K108 - Starter Lockout Relay
K109 - Def Lines Heater Relay
K110 - Def Supply Module
K111 - Aftertreatment Sensors Power Relay
K112 - Outrigger Lighting
K113 - Ignition Power Relay
K301
AIR HEATER
RELAY
K302
ENGINE
START
RELAY
132
205
22
148
23
403
401
402
131
130
137
142
30
17
130
132
21
28
205
149
152
136
151
135
140
401
402
80113724 B2
FIGURE A-1 continued
10087-2
To Next Page
Loading...
