Rohde & Schwarz SMW-K144 - Page 220

Remote-Control Commands
R&S
®
SMW-K144
220User Manual 1178.8013.02 ─ 06
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>[:CW<s2us0>]:PDSCh|PUSCh:CCODing:TBSize?............................. 227
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>[:CW<s2us0>]:PDSCh|PUSCh:CCODing:RVINdex.............................227
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:CSI1:BITS...................................................................228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:CSI2:BITS...................................................................228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:ACK:BITS................................................................... 228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:CSI1:PATTern..............................................................228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:CSI2:PATTern..............................................................228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:PUSCh:UCI:ACK:PATTern.............................................................. 228
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:APMap:MAPCoordinates................................................................ 229
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:APMap:COL<s2us0>:ROW<s3us0>:IMAGinary................................ 229
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:APMap:COL<s2us0>:ROW<s3us0>:REAL.......................................229
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:APMap:COL<s2us0>:ROW<s3us0>:MAGNitude...............................230
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:BWPart<gr0>:
ALLoc<user0>:APMap:COL<s2us0>:ROW<s3us0>:PHASe.....................................230
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:
BWPart<gr0>:ALLoc<user0>:PDSCh|PUSCh:TYPE <PXschType>
Defines the PDSCH/PUSCH type by selecting the DCI format by that the PDSCH/
PUSCH content is defined.
Parameters:
<PXschType> F00 | F01 | F10 | F11
*RST: F00
Example: See Example "Configuring the PDSCH incl. PTRS settings"
on page 153.
Manual operation: See "PDSCH Type/PUSCH Type" on page 88
[:SOURce<hw>]:BB:NR5G:SCHed:CELL<ch0>:SUBF<st0>:USER<dir0>:
BWPart<gr0>:ALLoc<user0>:PDSCh:NCW <NumUserAllocCW>
For PDSCH, sets if one or two codewords are used.
Parameters:
<NumUserAllocCW> integer
Range: 1 to 2
*RST: 1
PDSCH/PUSCH Commands